Cisco CCNA Cisco Certified Network Associate CCNA (803) - 200-120 Exam Practice Test

A. interface FastEthernet 0/1 channel-group 1 mode desirable switchport trunk encapsulation dot1q switchport mode trunk interface FastEthernet 0/2 channel-group 1 mode desirable switchport trunk encapsulation dot1q switchport mode trunk

B. interface FastEthernet 0/1 channel-group 1 mode passive switchport trunk encapsulation dot1q switchport mode trunk interface FastEthernet 0/2 channel-group 1 mode passive switchport trunk encapsulation dot1q switchport mode trunk

C. interface FastEthernet 0/1 channel-group 1 mode active switchport trunk encapsulation dot1q switchport mode trunk interface FastEthernet 0/2 channel-group 1 mode active switchport trunk encapsulation dot1q switchport mode trunk

D. interface FastEthernet 0/1 channel-group 2 mode auto switchport trunk encapsulation dot1q switchport mode trunk interface FastEthernet 0/2 channel-group 2 mode auto switchport trunk encapsulation dot1q switchport mode trunk

A. anycast

B. podcast

C. multicast

D. broadcast

E. allcast

A. 2

B. 8

C. 4

D. 1

A. There is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

B. SW1's Fa0/1 interface is administratively shut down.

C. There is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

D. There is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.

A. Compression

B. Authentication

C. Message Integrity

D. Error Detection

E. Encryption

A. FastEthernet0/1 is connected to a host with multiple network interface cards.

B. Interface FastEthernet0/2 has been disabled.

C. Multiple devices are connected directly to FastEthernet0/1.

D. A hub is connected directly to FastEthernet0/5.

E. FastEthernet0/1 is configured as a trunk link.

F. FastEthernet0/5 has statically assigned MAC addresses.

A. PVST+

B. MSTP

C. RSTP

D. Mono Spanning Tree

A. Check the duplex mode for SwitchA's fa0/2 port.

B. Check the trunk encapsulation mode for SwitchA's fa0/2 port.

C. Check the duplex mode for SwitchC's fa0/1 port.

D. Check the trunk encapsulation mode for SwitchC's fa0/1 port.

A. Full-duplex interfaces use CSMA/CD logic, so mismatches may be disguised by collisions.

B. 1-Gbps interfaces are full-duplex by default.

C. The symptoms of a duplex mismatch may be intermittent.

D. The interface displays a connected (up/up) state even when the duplex settings are mismatched.

E. Autonegotiation is disabled.

A. The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.

B. The network administrator can apply port security to EtherChannels.

C. The network administrator can apply port security to dynamic access ports.

D. When dynamic MAC address learning is enabled on an interface, the switch can learn new addresses, up to the maximum defined.

E. The network administrator can configure static secure or sticky secure MAC addresses in the voice VLAN.

A. No further routing configuration is required.

B. These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)# network 172.19.0.0

C. These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172.19.0.0

D. These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0

A. Syslog server

B. Other terminals

C. Flash

D. The console terminal

E. The logging buffer .RAM