Cisco Designing Cisco Data Center Infrastructure - 300-610 Exam Practice Test

Refer to the exhibit. A Cisco engineer is configuring a data center design scenario with Cisco MDS 9000 Series Switches. The cut-through routing mode is chosen for improved read operation performance. Each iSCSI host requires access to storage through the IPS module. First, the engineer configures the TCP tuning parameters as enabled SACK, the maximum bandwidth of 1 Gbps, buffer size of 4096, keepalive timeout at 1s, and enables Path MTU. Then, the engineer must set the QoS of the ISCSI link. What is the maximum QoS value that must be set for the ISCSI session?

Correct Answer: D Vote an answer
A storage administrator receives reports of network delays when database software attempts to access the storage array. The virtual machines that host the database software are installed on different rack servers connected to the Cisco UCS Fabric Interconnect domain. The existing SAN switches are connected to the Fabric Interconnects using two 8 Gb port-channel interfaces to connect the storage array. The storage administrator has decided to deploy iSCSI storage with four 10 Gbps interfaces connected to the Cisco UCS Fabric Interconnects.
Which deployment type resolves the problems with storage contention?

Correct Answer: D Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
A network administrator must create a redundant vHBA for the mission-critical virtual machines (VMs) installed on a Cisco UCS Fabric Interconnect blade server. The VMs access multiple datastores using VSAN55 and VSAN95. The datastore on which the VMs are hosted must be accessible if any of the uplinks goes offline. Which action meets these requirements?

Correct Answer: A Vote an answer
A SAN engineer needs to connect a Fibre Channel storage array to a Cisco MDS 9000 Series Switch by using an 8-Gbps interface. The switch must meet these requirements:
- ensure storage resilience
- prevent oversubscription
- guarantee the highest line rate for traffic processing
Which configuration should be applied for the interface on the switch to meet these requirements?

Correct Answer: D Vote an answer
What is a design consideration when implementing FSPF?

Correct Answer: A Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
What are two reasons to select OTV as the DCI solution to connect multisite topologies? (Choose two.)

Correct Answer: A,B Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
An engineer must create a solution for server deployment in a multitenant UCS environment with UCS Central. The solution must:
- Make use of centralized WWPN and IP pools.
- Define a unique network configuration for an organization.
Which action creates a solution that meets the requirements?

Correct Answer: C Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
Refer to the exhibit. A network engineer must improve high availability within the given UCS infrastructure. The engineer configured central nodes A and B in cluster mode to ensure that traffic fails over in the case of a network outage. Which type of redundancy will the cluster configuration provide?

Correct Answer: C Vote an answer
Refer to the exhibit. A corporation is working to enhance its data center services. A Cisco ACI solution is used for network services. Server_1 is currently running a high-traffic web application, and Server_2 is running a database server. The networking team is planning to install a load balancer and connect it to Leaf S3. For security reasons, all traffic from Server_1 destined to Server_2 must be redirected through the load balancer for load balancing. The solution must minimize the number of network hops, without requiring changes to the existing routing table.
Which action must the team take to configure service insertion in line with the specified requirements?

Correct Answer: D Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
Refer to the exhibit. The Cisco Nexus Series Switch with hostname Nexus1 is the default gateway for server A and server B. Both servers must have reachability to the internet, however, server A internet traffic must pass through the firewall for deep packet inspection. Also, the firewall must inspect any communication between server A and server B. Which solution must be applied to separate the data plane path for server A and server B?

Correct Answer: D Vote an answer
Which multicast rendezvous point redundancy mode is valid for Bidirectional PIM?

Correct Answer: B Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
A company is using Cisco UCS and wants a network orchestration solution to meet these requirements :
- centrally manage compute and storage platforms
- reduce the time it takes to detect an outage
- easily exchange data with TAC to reduce resolution times
The company does not have in-house knowledge about scripting.
Which solution must the company choose?

Correct Answer: D Vote an answer
An engineer must interconnect customer data centers by using a 10-Gbps, unicast-only, Layer 3 circuit. The requirement is to stretch the Layer 2 connection over the tunnel, isolate STP traffic, and create more than two million logical network segments. Which solution meets these requirements?

Correct Answer: C Vote an answer

Contact Us

If you have any question please leave me your email address, we will reply and send email to you in 12 hours.

Our Working Time: ( GMT 0:00-15:00 ) From Monday to Saturday

Support: Contact now 

日本語 Deutsch 繁体中文 한국어