DC0-200 by Dell Actual Free Exam Questions And Answers

Question 1

If there is a loss of power redundancy on your PowerEdge server, in which three ways can Dell OpenManage IT Assistant report this? (Choose three.)

A. An SNMP trap can be logged in the OpenManage IT Assistant.

B. The status panel for that system indicates which power supply failed.

C. Dell IT Assistant sends an alert to Dell OpenManage Server Administrator.

D. Systems Status is marked as "Warning" in OpenManage IT Assistant.

Discussion 0

Correct Answer: A,B,D Vote an answer

Question 2

The drive that contains the user home folders is running out of space. This partition is labeled D and is a part of a three disk RAID 5 labeled Virtual Disk 2. Yo u want to increase the size of the partition by adding an additional hard drive to the virtual disk. How can you do this when a PERC 3/Di is used?

A. Array Manager is used to expand the virtual disk onto an additional hard drive.

B. You back up the virtual disk. Array Manager is used to expand the virtual disk onto an additional hard drive.

C. You use Array Manager to delete Virtual Disk 2 and re-create it including the additional hard disk. You restore the contents of the original virtual disk from the RAID 5 parity.

D. You back up Virtual Disk 2. Array Manager is used to delete Virtual Disk 2 and recreate it including the additional hard disk. You re-create the D partition and restore its contents from tape.

Discussion 0

Correct Answer: D Vote an answer

Question 3

OpenManage Server Administrator can determine the status of which two server components? (Choose two.)

A. network activity

B. fans

C. disk utilization

D. memory

E. processor load

Discussion 0

Correct Answer: B,D Vote an answer

Question 4

What is the maximum number of primary partitions allowed by Array Manager for three disk arrays?

A. 15

B. 12

C. 6

D. 9

Discussion 0

Correct Answer: B Vote an answer

Question 5

What are three recommended solutions for resolving the error with a NIC which stop s communicating? (Choose three.)

A. You reseat the adapter in its slot or a different slot.

B. You install a different adapter in the same slot.

C. You remove and reinstall the drivers.

D. You confirm the Device List. Ctrl setting is set to Adapter-Enabled.

Discussion 0

Correct Answer: A,B,C Vote an answer

Question 6

You can use OMSA to remotely update the firmware for which two components? (Choose two.)

A. host bus adapter firmware

B. BIOS

C. Remote Access Controller firmware

D. system software

Discussion 0

Correct Answer: B,C Vote an answer

Question 7

You only configure a PowerEdge Server running Dell OpenManage Server Administrator with community names for read access. You then configure OpenManage IT Assistant to use the same community names for both read and write when configuring the subnet in ITA to discover that system. Which two management functions are you able to perform on that system from ITA? (Choose two.)

A. shut down the system remotely from ITA

B. discover and monitor the health of that system from ITA

C. log in to the system from ITA and change its temperature thresholds

D. see an inventory report of the system in ITA

Discussion 0

Correct Answer: B,D Vote an answer

Question 8

A disk in a RAID 5 array has failed. Using Array Manager, which statement is true about rebuilding the data onto a replacement drive if a PERC 3/DC is in use?

A. The rebuild operation will start automatically upon insertion of the replacement disk.

B. The replacement disk must be initialized after insertion.

C. The rebuild operation will start only after it is manually initiated.

D. The replacement disk must be initialized before insertion.

Discussion 0

Correct Answer: A Vote an answer

Question 9

You just added a new Dell PowerEdge server to the network. In order to use Dell OpenManage IT Assistant to manage it, which three steps do you need to take? (Choose three.)

A. install Dell OpenManage Management Station application on the new server

B. ensure that the new server's IP address is in the discovery specified for OpenManage IT
Assistant

C. install Dell OpenManage Remote Access Controller on the new server

D. install Dell OpenManage Managed System applications on the new server

E. verify the SNMP settings of the new server

Discussion 0

Correct Answer: B,D,E Vote an answer

Question 10

You are configuring network teaming on a PowerEdge server. The server has Windows 2000 installed and you do not know what network adapters are in the system. Without physically opening the chassis, what are two ways to see which network adapters are installed using the operating system? (Choose two.)

A. type ifconfig -a at a command prompt; on the description line, the manufacturer and device type will be named

B. type ipconfig /all at the command prompt; on the description line, the manufacturer and device type will be named

C. right-click My Computer, select Manage, left-click Device Manager, expand Network Adapters, and view installed adapters

D. right-click Network Neighborhood, select Properties, double-click Internet Protocol (TCP/IP), and view protocol-bound adapters

Discussion 0

Correct Answer: B,C Vote an answer

Dell Certified Server Professional - DC0-200 Exam Practice Test

Contact Us

Useful Links

Latest Updated