EMC Dell PowerEdge Professional - DCPPE-200 Exam Practice Test
An engineer is troubleshooting a blade server in an FX2s. The compute sled in SLOT 3 will NOT power on.
The engineer has taken the server down to minimum to POST. The server still does NOT power on. The engineer then swaps sleds SLOT 2 and 3. The iDRAC initializes in SLOT 2 but SLOT 3 is stuck at initializing the iDRAC.
What are two possible sources of the issue? (Choose two.)
The engineer has taken the server down to minimum to POST. The server still does NOT power on. The engineer then swaps sleds SLOT 2 and 3. The iDRAC initializes in SLOT 2 but SLOT 3 is stuck at initializing the iDRAC.
What are two possible sources of the issue? (Choose two.)
Correct Answer: A,C
Vote an answer
An engineer enters a data center to configure an uplink between an I/O Aggregator (IOA) and an upstream switch. The IOA and upstream switch are configured for spanning tree. The engineer applies the following configuration to the uplink port:
interface TenGigabitEthernet 0/12
switchport
flowcontrol rx on tx off
spanning-tree rstp edge-port
As soon as the engineer plugs in the cables, it creates a loop and brings down the network.
Which commands should be entered on the IOA to fix loop?
interface TenGigabitEthernet 0/12
switchport
flowcontrol rx on tx off
spanning-tree rstp edge-port
As soon as the engineer plugs in the cables, it creates a loop and brings down the network.
Which commands should be entered on the IOA to fix loop?
Correct Answer: B
Vote an answer
An engineer responsible for server lifecycle management (e.g. Monitor, Update, Deploy) needs to build a monitoring strategy for a multi-vendor data center. The company has an established third party software as the monitoring and help desk system.
Which option should be used to integrate Dell Server hardware into this monitoring architecture?
Which option should be used to integrate Dell Server hardware into this monitoring architecture?
Correct Answer: C
Vote an answer
An engineer is configuring VLT between two MXL switches. The engineer runs a show vlt brief command on one of the MXLs and receives the status shown in the exhibit. What should the engineer verify to fix the issue?
Correct Answer: B
Vote an answer
An engineer is configuring a new FD332 storage sled into an existing chassis in SLOT 3. The FD332 is NOT being detected by the assigned node.
Which two tasks must an engineer complete so that the FD332 is detected by the node? (Choose two.)
Which two tasks must an engineer complete so that the FD332 is detected by the node? (Choose two.)
Correct Answer: A,E
Vote an answer
An engineer is deploying a chassis with four IOAs and connecting it to the top of rack (ToR) switch. The deployment mandate requires that the switches be presented as one logical unit. Future servers can be added to network with the minimal amount of configuration.
The following steps have been completed:
- IOAs are daisy-chained using ports 9 and 10
- Cabled ports 11 and 12 on IOA 1 to the ToR
- Configured a team on NIC ports 1 and 2 on the server
How should the IOMs be configured?
The following steps have been completed:
- IOAs are daisy-chained using ports 9 and 10
- Cabled ports 11 and 12 on IOA 1 to the ToR
- Configured a team on NIC ports 1 and 2 on the server
How should the IOMs be configured?
Correct Answer: A
Vote an answer
An engineer needs to connect ports 49 and 53 on an MXL to a top of rack (ToR) switch in an LACP port channel.
The ToR switch has ports 46 and 60 configured in port channel 100.
Which configuration will successfully bring up the port channel on the MXL?
The ToR switch has ports 46 and 60 configured in port channel 100.
Which configuration will successfully bring up the port channel on the MXL?
Correct Answer: B
Vote an answer
An engineer is running an inventory report on a VRTX chassis group for a customer. When the engineer views the report, the engineer notices the inventory of one of the VRTX is missing one of its nodes.
What is the cause?
What is the cause?
Correct Answer: A
Vote an answer
Refer to the exhibit.
An engineer sets up FCoE boot on their server. The server fails during post.
What needs to be added to the NIC settings/option ROM to make booting successful?
Correct Answer: B
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
An engineer is building a new cluster and is using software-defined storage. The FX2 has 4x FC430s and 2x FD332 sleds. The blades are ready to add storage.
How should the engineer configure the FD332 sleds to be used for local storage?
How should the engineer configure the FD332 sleds to be used for local storage?
Correct Answer: A
Vote an answer