HPE Network Switching Associate - HPE6-A86 Exam Practice Test
Based on the example below:
show vsf
Force Autojoin : Disabled
Autojoin Eligibility Status : Not Eligible
MAC Address : ec:67:94:c4:77:80
Secondary : 2
Topology : Ring
Status : No Split
Split Detection Method : mgmt
Mbr Mac Address Type Status
ID
--- ------------------- ------- ----------
1 ec:67:94:c4:77:80 R8Q69A Conductor
2 ec:67:94:c4:37:80 R8Q69A Standby
3 ec:67:94:c5:7f:80 R8Q68A Member
What happens if the VSF link between members 1 and 2 is disconnected?
show vsf
Force Autojoin : Disabled
Autojoin Eligibility Status : Not Eligible
MAC Address : ec:67:94:c4:77:80
Secondary : 2
Topology : Ring
Status : No Split
Split Detection Method : mgmt
Mbr Mac Address Type Status
ID
--- ------------------- ------- ----------
1 ec:67:94:c4:77:80 R8Q69A Conductor
2 ec:67:94:c4:37:80 R8Q69A Standby
3 ec:67:94:c5:7f:80 R8Q68A Member
What happens if the VSF link between members 1 and 2 is disconnected?
Correct Answer: B
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
You are troubleshooting a connectivity issue and are reviewing your notes after talking to your team. Classify each piece of information as either a symptom or a possible cause. Matches may be used more than once.
Correct Answer:
Explanation:
A new firewall rule has been added = Cause
My email is not working = Symptom
My device says "No Internet" = Symptom
One of the DNS servers is offline = Cause
The switch firmware was upgraded = Cause
Websites are not loading = Symptom
The correct classification separates observed user impact from likely reasons for that impact. A symptom is what users or administrators observe, such as "email is not working," "No Internet," or "websites are not loading." These describe the effect of the problem but do not identify why it is happening. A cause is a condition, change, or failure that could explain the symptom. A newly added firewall rule could block traffic, an offline DNS server could prevent name resolution, and a firmware upgrade could introduce a configuration, compatibility, or service-change issue. HPE Aruba Networking troubleshooting documentation commonly separates symptoms from causes and corrective actions; for example, AOS-CX troubleshooting sections describe a visible symptom, then identify the cause and action needed to resolve it. This method helps avoid guessing and keeps troubleshooting structured: first collect symptoms, then identify recent changes and infrastructure failures that could be possible causes. In this question, the user-facing service failures are symptoms, while the firewall, DNS, and firmware items are possible causes.
You are about to log a support case with TAC for an issue with your HPE Aruba Networking CX switch.
What should you have ready in advance to provide them?
What should you have ready in advance to provide them?
Correct Answer: C
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
New IoT devices cannot obtain an IP address from a DHCP server at 10.200.1.51. Based on the output below, what should you configure to resolve the issue?
interface vlan100
description IoT
ip address 10.100.1.1/24
exit
interface 1/1/16
no shutdown
description Thermostat
vlan access 100
spanning-tree port-type admin-edge
exit
interface vlan100
description IoT
ip address 10.100.1.1/24
exit
interface 1/1/16
no shutdown
description Thermostat
vlan access 100
spanning-tree port-type admin-edge
exit
Correct Answer: C
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
What is the default behavior of a trunked port on an HPE Aruba Networking CX switch?
Correct Answer: D
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
You are trying to configure VSF on a pair of HPE Aruba Networking CX 8100 Series switches. What would cause the following error?
Switch-1(config)# vsf member 2
Invalid input: vsf
Switch-1(config)#
Switch-1(config)# vsf member 2
Invalid input: vsf
Switch-1(config)#
Correct Answer: C
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
When explaining the HPE Aruba Networking CX Virtual Switching Framework functionality on a CX 6200F switch to a customer, which statement about VSF ports is true?
Correct Answer: B
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
What describes the use of the Network Analytics Engine?
Correct Answer: A
Vote an answer
What is a characteristic of a static route?
Correct Answer: A
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).
You are about to start the initial configuration of an HPE Aruba Networking CX 6200M switch.
How would you connect to the switch to configure the SVI static IP address?
How would you connect to the switch to configure the SVI static IP address?
Correct Answer: A
Vote an answer
Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).