NS0-094 by Network Appliance Actual Free Exam Questions And Answers

Question 1

When you plan an ONTAP upgrade, which NetApp tool generates a detailed upgrade plan?

A. Active IQ Config Avisor

B. Upgrade Advisor

C. ONTAP System Manager

D. Active IQ Unified Manager

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 2

A NetApp node fails to boot and displays repeated boot-loop behavior after hardware maintenance. Which troubleshooting step should be performed FIRST?

A. Reset all cluster licenses

B. Replace every disk in the shelf

C. Verify recently installed FRUs and cable seating

D. Destroy the root aggregate

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 3

Which RAID type provides protection against three disk failures?

A. RAID-TEC

B. RAID 5

C. RAID DP

D. RAID 4

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 4

A customer reports intermittent cluster communication failures after moving equipment to a new rack. Which issue is MOST likely?

A. Excessive aggregate snapshots

B. Incorrect rack cabling or interconnect placement

C. ONTAP licensing expiration

D. Disk encryption mismatch

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 5

Which two steps are required to replace a drawer in a DS460c shelf? (Choose two.)

A. Evacuate all drives in the drawer.

B. Power off the shelf.

C. Disconnect the cable chains from the chassis.

D. Shut down both nodes.

Discussion 0

Correct Answer: A,C Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 6

When you add a new disk to an ONTAP 9.1 system, you see an error that the disk "has raid label with version (16), which is not within the currently supported range (14-15)." What is one possible cause of this error?

A. The disk was in a system with a newer version of ONTAP software

B. The disk needs to be assigned to the new system.

C. The disk is a non-zeroed spare.

D. The disk firmware is too new for ONTAP software.

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 7

You have upgraded your cluster from ONTAP 9.5 software to ONTAP 9.7 software. After two days, you notice that the upgrade is causing issues. You decide to revert to ONTAP 9.5 software.
Which two actions do you need to complete before you revert? (Choose two.)

A. Reinstall your boot media and install ONTAP 9.5 software.

B. Revert from ONTAP 9.7 software to ONTAP 9.6 software and then to ONTAP 9.5 software.

C. Delete all Snapshot copies from the past two days.

D. Wipe your config and restore from backup.

Discussion 0

Correct Answer: A,D Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 8

Which two of the following methods are valid ways to access a node which is not booting?
(Choose two.)

A. Service Processor

B. serial console

C. cluster management port

D. node management port

Discussion 0

Correct Answer: A,B Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 9

You have replaced the cluster backend switches on a 4-node NetApp ONTAP cluster with new switches. After the replacement, you realize that the system shows errors for the old switches that were removed:

You also notice that system switch ethernet showshows four switches, the two old switches and the two new switches.
What action will resolve the issue?

A. Reconnect the old switches and download a support bundle using the system switch ethernet log collect command.

B. Perform a reboot of the affected node using the storage failover takeover command.

C. Delete the old switches from the database using the system switch ethernet delete command.

D. Clear the health alert using the system health alert delete command.

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Network Appliance NetApp Hardware Support Engineer Professional - NS0-094 Exam Practice Test

Contact Us

Useful Links

Latest Updated