NS0-182 by Network Appliance Actual Free Exam Questions And Answers

Question 1

You are preparing to install a new cluster at a customer site.
Which two concerns must you address with the customer in this scenario? (Choose two.)

A. Is there an uninterruptible power supply (UPS) system?

B. Is there a fire extinguishing system?

C. Are the power requirements fulfilled?

D. Is there enough rack space available?

Discussion 0

Correct Answer: A,B Vote an answer

Question 2

What is the minimum number of iSCSI LIFs per node in ONTAP 9.5?

A. 2

B. 4

C. 3

D. 1

Discussion 0

Correct Answer: A Vote an answer

Question 3

A customer wants to expand a 10-node AFF A700s NAS cluster running with Cisco Nexus 3132Q-V cluster interconnect switches using new nodes.
In this scenario, what is the maximum number of nodes to be added into this cluster?

A. 2

B. 12

C. 14

D. 24

Discussion 0

Correct Answer: A Vote an answer

Question 4

An iSCSI LIF fails to migrate during a storage failover test.
In this scenario, why did the LIF not migrate?

A. The failover policy was not configured.

B. A failover port was not defined.

C. LIFs that serve block protocols do not failover.

D. LIF failover was not enabled.

Discussion 0

Correct Answer: C Vote an answer

Question 5

You have just completed the installation of a FAS9000 HA pair with ONTAP 9.5.
In this scenario, according to NetApp best practices, which two tests verify the HA failover functionality?
(Choose two.)

A. Invoke a system core.

B. Pull the motherboard out of the slot.

C. Disconnect the HA interconnect cabling.

D. Power cycle the node.

Discussion 0

Correct Answer: A,D Vote an answer

Question 6

In which two configurations would Advanced Drive Partitioning be used by default in ONTAP 9.5? (Choose two.)

A. a FAS9000 with one shelf DS212C with 24 800 GB SAS HDDs

B. a FAS8040 with one DS2246 shelf containing 24 900 GB SAS disks

C. an AFF A700 with one DS2246 shelf containing 24 960GB SSDs

D. a FAS2554 with 24 internal 1000 GB SATA HDDs

Discussion 0

Correct Answer: B,C Vote an answer

Question 7

You are configuring a new system with ONTAP 9.5. You created interface groups, VLANs, and a broadcast domain for the new ports on all the nodes of your cluster. During the configuration, you used an MTU value of
1500 for the broadcast domain and 9000 for the physical ports. The customer asks you to enable jumbo frames.
What should you do in this scenario?

A. Change the MTU value to 9000 on the ifgroup.

B. Set the MTU option to jumbo frames on the ifgroup.

C. Set the MTU option to jumbo frames on the broadcast domain.

D. Change the MTU value to 9000 on the broadcast domain.

Discussion 0

Correct Answer: D Vote an answer

Question 8

You installed a new AFF A800 2-node ONTAP 9.5 cluster and are asked to run diagnostics to validate the hardware.
Which command is used from the loader prompt to enter diagnostics?

A. printenv

B. boot_diags

C. sldiag

D. savenv

Discussion 0

Correct Answer: B Vote an answer

Question 9

You configured AutoSupport and are trying to send a full AutoSupport message to NetApp. You use the autosupport history show command and see the output shown in the exhibit. The customer confirms that the AutoSupport settings are correct.
Which two actions will solve this issue? (Choose two.)

A. The customer needs to enable AutoSupport for both nodes.

B. The customer needs to change the transport protocol to HTTP.

C. The customer needs to exclude the two nodes from the attachment-size limitation.

D. The customer needs to white-list the two nodes on their mail server.

Discussion 0

Correct Answer: A,B Vote an answer

Question 10

After performing a controller upgrade on an HA pair in an ONTAP 9.5 cluster, you want to decommission the old systems.
Which statement is correct in this scenario?

A. Ask
the customer to log in to http://mysupport.netapp.com and decommission the old systems.

B. Decommissioning is done automatically when the systems no longer send AutoSupport messages.

C. The systems do not need to be decommissioned because the serial numbers are overtaken by the new systems.

D. Open a Priority 1 technical case with NetApp Global Support and specify "Decommission" in the title.

Discussion 0

Correct Answer: A Vote an answer

Question 11

You want to grow your current ONTAP cluster. You have a Cisco Nexus 5596UP that is currently using all of its on-board ports.
Which statement is correct in this situation?

A. Add new SFP modules to the empty on board ports on the Cisco switches.

B. Pull the redundant cables from each node to obtain more free ports on the switch.

C. Add expansion modules to the Cisco switches.

D. Contact NetApp Support to order new switches.

Discussion 0

Correct Answer: C Vote an answer

Network Appliance NetApp Certified Storage Installation Engineer, ONTAP - NS0-182 Exam Practice Test

Contact Us

Useful Links

Latest Updated