3605 by Avaya Actual Free Exam Questions And Answers

Question 1

What is the maximum number of Gigabit Ethernet ports on a single Ethernet Routing Switch (ERS) 8300 Input/Output module?

A. 50

B. 24

C. 48

D. 16

Discussion 0

Correct Answer: C Vote an answer

Question 2

A switch with Simple Loop Prevention Protocol (SLPP) did not detect a loop.
What are two reasons this occurred? (Choose two)

Discussion 0

Correct Answer:

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 3

One of the switches in the Ethernet Routing Switch (ERS) stacks files and is replaced. The auto unit replacement (AUR) is enabled but the stack is not functioning properly. What is the problem?

A. the stack power was left on during the switch replacement.

B. The stack has two switches with Force Stack disabled.

C. The switches in the stack are not identical

D. The switches in the stack are not running the same release of software

Discussion 0

Correct Answer: A Vote an answer

Question 4

A customer needs to install a new Ethernet Routing Switch (ERS) 2550T on the 172.16.5.0/24
network, but does not have a
console
cable available.
Which statement is correct?

A. To communicate with an ERS 2550T the IP address must first be set though the console interface.

B. The customer
can set the switch to use the temporary
address of
192.168.192.168 by pressing the User Interface button on the front of the ERS 2550T

C. The switch will first attempt to use BootP to acquire an IP address, and if that fails it will assign IP address 192.160.1.1/24 to the switch IP.

D. The customer can connect to the network management Ethernet port which is pre-configured to use the 192 168 1 1/24 IP address

Discussion 0

Correct Answer: D Vote an answer

Question 5

The Ethernet Routing Switch (ERS) 8600 supports the feature IP VPN-Lite that does not require the use of an MPLS network. Which function does the ERS 8600 as a Provider Edge (PE) perform for IP VPN-Lite?'

A. The PE provides route exchange with remote PE devices using OSPF.

B. The PE uses the Virtual Routing Forwarding (VRF) instances to provide traffic separation.

C. The PE adds a shim header to the Ethernet header specifying which network the packet is crossing.

D. The PE incorporates Label Distribution Protocol across the core network to connect remote PE devices.

Discussion 0

Correct Answer: B Vote an answer

Question 6

Refer to the exhibit.

Based on the command line output shown in the exhibit, how many Gigabit Ethernet ports are available on this Ethernet Routing Switch (ERS) 8600?

A. 52

B. 3

C. 83

D. 48

Discussion 0

Correct Answer: D Vote an answer

Question 7

A campus network requirement is to introduce Virtual Routing and Forwarding (VRF) in the existing Ethernet Routing Switch (ERS) 8600-based core. The technician has to configure VRF on the ERS 8600. Which statement represents the order for configuring a new VRF?

A. Create a VRF, change context to the new VRF, create a new VLAN, add an IP address to the VLAN.

B. Create VRF, change context to the new VRF, add an IP address, create a new VLAN, and move the VLAN to the new VRF.

C. Creating a new VLAN, add an IP address to the VLAN, create the VRF in the VLAN configuration.

D. Create a VRF, create a new VLAN, move the VLAN to the new VRF, change context to the new VRF, and add an IP Address.

Discussion 0

Correct Answer: D Vote an answer

Question 8

A campus network requirement is to introduce Virtual Routing and Forwarding (VRF) in the existing Ethernet Routing Switch (ERS) 8000-based core. The technician has to configure VRF on the ERS 8000. Which statement represents the order for configuring a new VRF?

A. Create a new VLAN, add an IP address, create a VRF, and move the VLAN to the new VRF.

B. Create a VRF, create a new VLAN, move the VLAN to the new VRF, and add an IP address.

C. Create a VRF, add an IP address, create a new VLAN, and move the VLAN to the new VRF.

D. Create a VRF, create a new VLAN, add an IP address, and move the VLAN to the new VRF.

Discussion 0

Correct Answer: B Vote an answer

Question 9

After issuing a show mit ist stats (CLI) or show ist stat (ACLI) command, it is
determined that running type is normal MLT and not Inter Switch Trunks (IST).
Which are two causes of the 1ST not running properly? (Choose two.)

A. The peer IP addresses have to be 192.168.1.1/30 and 192.168.1.2/30.

B. The MLT ID does not match on both switches.

C. The peer IP address is not the address of the peer switch 1ST VLAN

D. The 1ST is not enabled on both switches.

Discussion 0

Correct Answer: C,D Vote an answer

Question 10

In a multicast
campus, when
should
the
PIM
interface in passive
mode
be configured?

A. When there are no unicast routing paths

B. When more than one multicast routing protocol is in use

C. When PIM control traffic must be passed

D. When the ERS 8600 is used as an edge switch and is aggregating end users

Discussion 0

Correct Answer: D Vote an answer

Question 11

The exhibit indicates the two show commands from an edge Ethernet Routing Switch (ERS) 5520- 24T-PWR an untagged frame arrives on port 10.which is configured as an access port. To which VLAN will the packet be forwarded?

A. All untagged packets will be discarded.

B. All untagged packets will be placed in VLAN 31?

C. All untagged packets will be placed in the default VLAN (VLAN 1).

D. All untagged packets will be placed in VLAN 311

Discussion 0

Correct Answer: A Vote an answer

Question 12

1ST
configuration using the
show mlt
ist info command, which IP
address should be in the
IP ADDRESS column?

A. the IP address of the IST VL AN on the peer switch . the IP address of the IST on the peer switch

B. the IP address of the ISTVLAN on the local switch

C. the management IP address of the peer switch

Discussion 0

Correct Answer: A Vote an answer

Avaya Ethernet Routing Switch Implementation and Maintenance - 3605 Exam Practice Test

Contact Us

Useful Links

Latest Updated