HPE7-A06 by HP Actual Free Exam Questions And Answers

Question 1

Refer to the exhibit and code sample.

What is the effect when you add the statement "neighbor 10.2.0.3 send-community both" to the ipv4 address family? (Choose two.)

A. It causes R1 to negotiate the ability to send and receive standard and extended communities with R2.

B. It will cause existing BGP peering between R1 and R2 to flap.

C. The feature will be enabled without consequence to the R1 established session with R2.

D. It causes R1 to allow the exchange of communities with NLRI records in both inbound and outbound direction.

E. It causes R1 to negotiate for the ability to import and export all type-1 and type-2 communities with R2.

Discussion 0

Correct Answer: A,D Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 2

You are tasked with describing VSX to a colleague. Select the three items that are considered best practices for implementing VSX on AOS-CX. (Choose three.)

A. Configure all VLANs manually on both the primary and secondary nodes before enabling vsx-sync.

B. Set a VSX system-mac manually to simplify switch replacement of the primary if required.

C. Use a direct L3 circuit for the keepalive connection between both nodes.

D. Adjust the default keepalive timers to match or exceed the ISL hold interval.

E. Allow VLAN 1 on all trunks in order to facilitate ZTP for downstream devices.

F. Adjust MTU on the ISL link to permit transport of jumbo frames if endpoints require it.

Discussion 0

Correct Answer: B,C,F Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 3

The customer wants to configure ARP inspection on VLAN 6 port 1/1/2 but not on port 1/1/1.
What are the correct commands to establish this?

A.

B.

C.

D.

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 4

Refer to the exhibit.

The customer has VSX clusters in two locations interconnected over on MC-LAG interface. You need to SVI to provide a seamless experience for clients connected to Edge-1 and Edge-2 switches to reach the default route if the resources are moved between the switches.
What needs to be done as an HPE Aruba Networking best practices?

A. Configure the VXLAN interface and bind required SVIs as VNIs.

B. Configure active forwarding and use the same virtual IP and a different vMAC.

C. Configure VRRP and load balance traffic using member properties.

D. Configure the active gateway and use the same virtual IP and vMAC.

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

Question 5

During troubleshooting, an engineer finds excessive ARP requests in the network. Which setting could mitigate this issue?

A. Enabling DHCP Snooping

B. Adjusting MAC aging timers

C. Configuring proxy ARP

D. Increasing ARP cache size

Discussion 0

Correct Answer: A Vote an answer

Question 6

A customer requires multiple VLANs on an HPE campus network. Which configuration is essential on the switch interfaces connected to other switches to ensure VLAN traffic passes through?

A. Enable LACP on the interfaces

B. Set the interfaces as trunk ports

C. Configure the interfaces as access ports

D. Enable DHCP relay on the interfaces

Discussion 0

Correct Answer: B Vote an answer

Question 7

A pair of CX 8325 series switches is configured in a VSX cluster. Which function is executed on both VSX members during normal operation?

A. replies to ARP requests with the cluster vMAC

B. relays DHCP requests or servers DHCP offer

C. routes PIM and PIM-DR

D. periodically sends gratuitous ARP and broadcast hello packets

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for Fast2test members. You can sign-up / login (it's free).

HPE Campus Access Switching Expert Written - HPE7-A06 Exam Practice Test

Contact Us

Useful Links

Latest Updated