NS0-181 by Network Appliance Actual Free Exam Questions And Answers

Question 1

What is the main function of ACP?

A. It enables the automatic shelf ID assignment.

B. It allows the controller to nondisruptively reset the SAS expanders.

C. It allows cabling the shelf to two additional controllers.

D. It allows the controller to use Ethernet instead of SAS to fetch the storage data.

Discussion 0

Correct Answer: D Vote an answer

Question 2

You install a new FAS26xx HA system with ONTAP 9.1 at a customer's site. After cabling the SAS cables, the customer wants to cable Alternate Control Path (ACP). But the FAS26xx has no physical port for ACP.
Which statement is correct in this scenario?

A. Beginning with ONTAP 9 software. ACP cabling for disk shelves is no longer required.

B. Within a FAS HA system, the ACP function is established over the cluster interconnect

C. To reach the ACP function, you should put the ACP cable into one of the onboard Ethernet pons.

D. The ACP function is established over the customer network.

Discussion 0

Correct Answer: A Vote an answer

Question 3

You were dispatched to add a DS224C to an existing HA pair that has a stack of DS4243 shelves with 1 TB drives and a stack of DS4246 shelves with 1 TB drives. The customer wants to make sure that ACP is cabled for all shelves.
Which two considerations should you advise the customer in this situation? (Choose two.)

A. ACP communication uses SAS cables and does not require Ethernet cables for IOM12 and IOM6 modules.

B. The ACP communication has been discontinued beginning with ONTAP 9.1, IOM6, and IOM12 modules.

C. ACP communication cannot be used for the DS224C and the DS4243 shelves at the same time.

D. Out-of-band ACP communication is use by default in ONTAP 9.0 and later software.

Discussion 0

Correct Answer: A,D Vote an answer

Question 4

Referring to the exhibit, which statement describes the duster network used by the cluster interconnect ports?

A. The network that allows all nodes in the cluster to have direct access to every other node's disk shelves.

B. The network used to allow all nodes to communicate with the users for data access.

C. The network used to allow all nodes to communicate for internal (private) data access.

D. The network used to allow all nodes to communicate with the customer (or management access.

Discussion 0

Correct Answer: C Vote an answer

Question 5

After the installation of the NetApp CN1610 cluster switches, you want to verify that the cabling is correct.
Which protocol will allow you to verify the cabling remotely?

A. Cisco Discovery Protocol (CDP)

B. Hyper Text Transfer Protocol (HTTP)

C. Transmission Control Protocol (TCP)

D. Point to Point protocol (PPP)

Discussion 0

Correct Answer: C Vote an answer

Question 6

A node joins a cluster in ONTAP 9.1.
Which statement is correct about the NTP configuration in this situation?

A. A node that joins a cluster automatically adopts the NTP configuration of the cluster

B. A node that join a cluster has a separate NTP service.

C. A node that joins a cluster must reboot before running the NTP service.

D. A node that joins a cluster must be manually configured for NTP.

Discussion 0

Correct Answer: A Vote an answer

Question 7

You are asked to install an AFF A700 with two DS224C shelves fully populated. When you arrive, the customer asks you to install an additional shelf.
Which shelf would you add to this cluster?

A. a DS2246 shelf fully populated with SSD drives

B. a DS4486 shelf fully populated with SATA drives

C. a DS224C shelf fully populated with SAS drives

D. a DS224C shelf fully populated with SATA drives

Discussion 0

Correct Answer: A Vote an answer

Question 8

You have just installed a new FAS2620 on a cluster site. You are using the USB cable for the intial configuration.
In this scenario, what is the default speed for the serial connection?

A. 115200 bps

B. 9600 bps

C. 15200 bps

D. 576000 bps

Discussion 0

Correct Answer: A Vote an answer

Question 9

You need to verify the configuration currently loaded on a Cisco Nexus 3132Q-V cluster switch after applying the RCF.
Which command will accomplish this task?

A. Use the show running-config command

B. Use the verify config command.

C. Use the show startup-conf command.

D. Use the show bootvar command.

Discussion 0

Correct Answer: A Vote an answer

Network Appliance NetApp Certified Storage Installation Engineer - ONTAP 9.1 - NS0-181 Exam Practice Test

Contact Us

Useful Links

Latest Updated