Best Value Available! 2025 Realistic Verified Free CHFM Exam Questions
Pass Your Exam Easily! CHFM Real Question Answers Updated
NEW QUESTION # 13
To protect systems and life, GFCI systems monitor which of the following?
- A. voltage
- B. resistance
- C. power
- D. current
Answer: D
Explanation:
A Ground-Fault Circuit Interrupter (GFCI) continuously monitors the current balance between the "hot" and
"neutral" conductors. If an imbalance greater than about 5 milliamps occurs (indicating leakage current flowing to ground), the GFCI trips instantly to protect personnel from shock.
Correct (D): Current - GFCIs detect differences in current between conductors.
Incorrect: Resistance (A), Voltage (B), and Power (C) are not directly monitored by GFCIs.
References:
NFPA 70: National Electrical Code (NEC), Article 100 - GFCI definition.
OSHA Electrical Safety Standards, Subpart S - Requirement for GFCI personnel protection.
AHA/CHFM Exam Content Outline - Compliance domain, electrical safety requirements.
NEW QUESTION # 14
According to NFPA 80, the maximum undercut allowed for rated fire doors is how many inches?
- A. 5/8
- B. 1/2
- C. 3/4
- D. 0
Answer: C
Explanation:
NFPA 80 (Standard for Fire Doors and Other Opening Protectives) sets requirements for fire door construction and installation. It specifies that the maximum undercut clearance is 3/4 inch unless otherwise tested and listed. Greater clearances compromise the integrity of the fire barrier.
References: NFPA 80, Section 4.8.4 (2010 edition and later); CHFM Candidate Handbook - Compliance domain.
NEW QUESTION # 15
A construction project in a cafeteria should not start until which of the following is present?
- A. security authorization
- B. approval from a clinical director
- C. funding
- D. staffing
Answer: C
Explanation:
Construction projects in healthcare facilities must have secured funding before starting. While approvals, staffing, and security considerations are important, the project cannot begin without the capital budget authorization. This aligns with AIA project delivery requirements and AHA/ASHE guidance for healthcare construction projects.
References: AIA A201 General Conditions; AHA/ASHE CHFM Handbook - Planning, Design, and Construction domain.
NEW QUESTION # 16
Where a required fire alarm system is out of service for more than 4 hours in a 24-hour period, which of the following is required according to NFPA Life Safety Codes?
Notify the authority having jurisdiction.
Provide an approved fire watch for all parties left unprotected by the shutdown.
Notify the building administrator.
Notify the fire alarm service company for repair.
- A. 2 and 4 only
- B. 3 and 4 only
- C. 1 and 3 only
- D. 1 and 2 only
Answer: D
Explanation:
NFPA 101 (Life Safety Code, Section 9.6.1.6) requires that when a fire alarm system is out of service for more than 4 hours in a 24-hour period, the facility must (1) notify the authority having jurisdiction (AHJ) and (2) provide an approved fire watch until the system is restored. Internal notifications such as to administrators or vendors may occur, but the code specifically mandates AHJ notification and fire watch.
References: NFPA 101, Section 9.6.1.6; CHFM Candidate Handbook - Compliance domain.
NEW QUESTION # 17
Which of the following types of injuries is most likely to occur during an MRI scanning process?
- A. radiation overexposure
- B. missile projection
- C. visual impairment
- D. permanent hearing loss
Answer: B
Explanation:
MRI does not use ionizing radiation, so radiation-related injuries are not possible. The greatest risk is the
"missile effect" where ferromagnetic objects (scissors, oxygen tanks, tools) are violently pulled into the MRI bore by its powerful magnetic field.
D). Missile projection (Correct): Most likely injury hazard.
A). Visual impairment: Not a typical MRI injury.
B). Radiation overexposure: MRI uses magnetic fields, not radiation.
C). Hearing loss: Possible from loud noise but mitigated with ear protection; less common than missile hazard.
References:
FDA MRI Safety Guidelines.
ACR (American College of Radiology) MRI Safety Practices.
CHFM Candidate Handbook - Compliance domain.
NEW QUESTION # 18
The Resource Conservation and Recovery Act (RCRA) was enacted to protect public health from
- A. improper disposal of used needles.
- B. improper medical waste management.
- C. hospital incinerator emissions.
- D. improper management of hazardous wastes.
Answer: D
Explanation:
The RCRA (1976) governs the proper management of hazardous waste from generation to disposal ("cradle to grave"). While healthcare organizations often think of sharps or medical waste, RCRA is broader, addressing hazardous chemicals, solvents, and pharmaceuticals. Medical waste is regulated under other federal and state rules.
References: U.S. Environmental Protection Agency, RCRA Overview; CHFM Handbook - Compliance domain.
NEW QUESTION # 19
The time that materials or assemblies have withstood a fire exposure, as established in accordance with test procedures of NFPA 251, is referred to as the
- A. fire protection rating.
- B. fire assembly rating.
- C. fire resistance rating.
- D. flame spread rating.
Answer: C
Explanation:
According to NFPA 251 (Standard Methods of Tests of Fire Resistance of Building Construction and Materials), once a material or assembly is tested and a measure of time is obtained, that result is defined as the fire resistance rating. This rating expresses the duration that a building element can withstand a standardized fire exposure while maintaining structural integrity.
* Correct Answer (B. fire resistance rating): NFPA 251 specifically defines this as the time result from fire exposure testing. It applies to walls, floors, and structural assemblies.
* Incorrect Options:
* A. flame spread rating: This measures only the surface burning characteristics of materials, determined using ASTM E84 or UL 723, not the endurance of an entire assembly.
* C. fire assembly rating: This is not an officially recognized NFPA term; the proper terminology is fire resistance rating.
* D. fire protection rating: This applies to opening protectives such as doors, windows, or shutters, which are tested using NFPA 252 or NFPA 257, not NFPA 251. Fire protection ratings are distinct from fire resistance ratings, since they do not measure full structural endurance.
Relevance to CHFM Compliance Domain:
The Certified Health Care Facility Manager (CHFM) exam includes compliance with fire and life safety codes under its "Compliance" content area. The CHFM Candidate Handbook emphasizes the requirement to understand and apply NFPA standards in healthcare facilities, ensuring compliance with regulatory fire safety measures such as those defined in NFPA 251.
References:
NFPA 251: Standard Methods of Tests of Fire Resistance of Building Construction and Materials - Definition of "fire resistance rating." NFPA: Fire-Protection Ratings and Fire-Resistance Ratings-What's the Difference? - Clarification between assemblies (fire resistance) and openings (fire protection).
NFPA: Construction Types and Material Combustibility - Explanation of flame spread index under ASTM E84/UL 723.
American Hospital Association (AHA), CHFM Candidate Handbook - Exam Content Outline, Compliance domain, which includes NFPA fire safety requirements.
NEW QUESTION # 20
A "WAGD" outlet would typically be found in the
- A. laundry room.
- B. electrical closet.
- C. boiler room.
- D. operating room.
Answer: D
Explanation:
"WAGD" stands for Waste Anesthetic Gas Disposal. These outlets are installed in operating rooms to remove excess anesthetic gases exhaled by patients or escaping from anesthesia equipment. The purpose is to maintain staff safety and compliance with NFPA 99 (Health Care Facilities Code), which requires WAGD systems in anesthetizing locations.
Correct (D): Operating rooms require WAGD outlets as part of medical gas and vacuum systems.
Incorrect:
A). boiler room: No patient care; WAGD outlets are not relevant.
B). electrical closet: For electrical equipment only, no medical gases.
C). laundry room: Handles linens, not anesthetic gas removal.
References:
NFPA 99: Health Care Facilities Code - Requirements for WAGD systems in anesthetizing locations.
AHA/CHFM Study Outline - Maintenance and Operations domain covering utility and gas systems.
NEW QUESTION # 21
After a recent lighting retrofit, the measured load on the affected lighting panel is 110 amps at 277 volts. The load is constant for 100 hours each week. Assuming the power factor to be 1, what is the annual energy consumption in kWh?
- A. 158,444
- B. 15,844,400
Step-by-Step Calculation:
Power (kW) = Volts × Amps ÷ 1000 = 277 × 110 ÷ 1000 = 30.47 kW
Weekly consumption = 30.47 × 100 hr = 3,047 kWh/week
Annual consumption = 3,047 × 52 = 158,444 kWh/year - C. 1,584.44
- D. 15,844.4
Answer: A
Explanation:
The correct calculation shows an annual energy consumption of 158,444 kWh. Smaller values (A and B) underestimate by factor of 10, while D overestimates by factor of 100.
References: NFPA 70; ASHE Energy Management Guidelines; CHFM Financial Management domain.
ChatGPT said:
NEW QUESTION # 22
Engineering controls required by the CDC for TB isolation rooms include
- A. respirator fit testing of engineering employees.
- B. engineering departmental policies and procedures.
- C. use of personal protective equipment.
- D. negative air pressure of rooms.
Answer: D
Explanation:
CDC Guidelines for Preventing the Transmission of Mycobacterium tuberculosis in Health-Care Facilities (1994, reaffirmed in later updates) require negative pressure isolation rooms as a primary engineering control.
This ensures airflow moves into the room and is exhausted to the outside or through HEPA filtration. PPE and respirator fit testing are administrative or personal controls, not engineering.
References: CDC Guidelines for TB Control; NFPA 99; ASHRAE 170.
NEW QUESTION # 23
Construction and/or renovation project submittals and shop drawings are reviewed to ensure
- A. code compliance.
- B. the project has minimal change orders.
- C. compliance with plans and specifications.
- D. the contractor understands the intent of the specifications.
Answer: C
Explanation:
Submittals and shop drawings are specifically reviewed to ensure compliance with the design intent, plans, and specifications prepared by the architect/engineer. Code compliance is established during design and permitting, while minimizing change orders or ensuring contractor understanding are indirect benefits.
References: AIA A201 General Conditions; AHA/ASHE CHFM Handbook - Planning, Design, and Construction domain.
NEW QUESTION # 24
When storing oil or petroleum products over 1,320 gallons above ground or 42,000 gallons underground, a Spill Prevention, Control, and Countermeasure (SPCC) program is required in accordance with
- A. The Joint Commission Utility Management standards.
- B. OSHA Regulations 1926.153 Liquefied Petroleum Gas Act.
- C. NFPA 430 Storage of Liquid and Solid Oxidizers.
- D. Federal Regulations 40 CFR Part 112 Oil Pollution Act.
Answer: D
Explanation:
The requirement for Spill Prevention, Control, and Countermeasure (SPCC) planning is specifically mandated under Federal Regulations 40 CFR Part 112, under the Clean Water Act (Oil Pollution Act amendments).
Facilities with aboveground storage exceeding 1,320 gallons or underground storage over 42,000 gallons must develop and implement an SPCC plan to prevent oil discharges into navigable waters.
Correct Answer (A): Federal 40 CFR Part 112 establishes the threshold quantities and program requirements.
B (Joint Commission): TJC standards govern utility management but do not set SPCC requirements.
C (OSHA 1926.153): This regulation applies to liquefied petroleum gas safety, not petroleum or oil spill prevention.
D (NFPA 430): Governs oxidizers, not oil storage or spill prevention.
References:
Federal Regulation 40 CFR Part 112, Oil Pollution Prevention.
American Hospital Association, CHFM Candidate Handbook - Compliance and Environment of Care standards reference environmental and regulatory codes.
NEW QUESTION # 25
Which scenario is best for managing an inventory of repair parts?
- A. Purchase one spare part in inventory for all patient equipment parts in use.
- B. Purchase spare parts from suppliers as replacements are needed.
- C. Purchase critical spare parts from suppliers on an annual basis.
- D. Purchase one spare part in inventory for each part in use.
Answer: A
Explanation:
Best practice in healthcare facilities management is to keep one critical spare part for each unique piece of patient-care equipment (not for every unit). This approach balances patient safety and risk mitigation while avoiding excessive storage costs.
A: "As needed" creates downtime risk.
B: Annual bulk purchase may leave gaps in urgent needs.
D: One-for-one spares is excessive, costly, and impractical.
References: ASHE/AHA CHFM study guide - Maintenance and Operations; The Joint Commission EOC standards.
NEW QUESTION # 26
Which section of the National Electrical Code addresses the installation of electrical wiring within healthcare facilities?
- A. Article 517
- B. Article 514
- C. Article 555
- D. Article 551
Answer: A
Explanation:
The National Electrical Code (NEC) Article 517 governs the installation of electrical systems in healthcare facilities, including patient care areas, essential electrical systems, and life safety branches.
A: Article 514 - Motor Fuel Dispensing Facilities.
C: Article 551 - Recreational Vehicles and RV Parks.
D: Article 555 - Marinas and Boatyards.
References: NFPA 70 (NEC), Article 517.
NEW QUESTION # 27
What is the maximum capacity of soiled linen or trash receptacles allowed in patient rooms or nurse stations?
- A. 16 gal.
- B. 32 gal.
- C. 64 gal.
- D. 8 gal.
Answer: B
Explanation:
Comprehensive and Detailed Explanation From Exact Extract:
Per NFPA 101: Life Safety Code, the maximum allowable capacity for soiled linen or trash receptacles located outside of hazardous storage rooms (such as within patient rooms or nurse stations) is 32 gallons (121 liters). If containers are larger than this, they must be stored in a room meeting hazardous area protection requirements.
* Correct Answer (C. 32 gal.): Matches NFPA 101, 18/19.7.5.5.7 (Health Care Occupancies), which restricts container size to 32 gallons maximum unless in a protected hazardous storage room.
* Incorrect Options:
* A. 8 gal. and B. 16 gal. - These are not the standard NFPA thresholds.
* D. 64 gal. - Exceeds NFPA's maximum; would require special hazardous storage protections.
Relevance to CHFM: This falls under the Compliance domain, as CHFM professionals must ensure healthcare facilities follow NFPA 101 and Joint Commission standards regarding fire and life safety.
References:
NFPA 101: Life Safety Code, Section 18/19.7.5.5.7 - Waste and linen receptacle capacity limits.
CHFM Candidate Handbook - Compliance domain includes NFPA code interpretation and application.
NEW QUESTION # 28
NFPA 25 (2011) requires sprinkler system fire pumps to be tested in a flow condition at what frequency?
- A. quarterly
- B. weekly
- C. annually
- D. monthly
Answer: C
Explanation:
NFPA 25 (2011), Standard for the Inspection, Testing, and Maintenance of Water-Based Fire Protection Systems, specifies that a fire pump flow test must be performed annually. This ensures that the pump delivers adequate flow and pressure under actual operating conditions. Weekly no-flow (churn) tests are also required, but full-flow condition testing is mandated at least once per year.
Reference: NFPA 25 (2011), Section 8.3.3.
NEW QUESTION # 29
According to NFPA 13, when replacing standard response sprinkler heads with quick response heads, all heads must be replaced in the entire
- A. zone.
- B. compartment.
- C. corridor.
- D. building.
Answer: B
Explanation:
NFPA 13 (Standard for the Installation of Sprinkler Systems) specifies that quick-response and standard- response sprinklers shall not be mixed within the same compartment. This is to ensure uniformity in activation and discharge characteristics.
A (Compartment): Correct, all heads in a compartment must match type.
B, C, D: NFPA does not require wholesale replacement across zones, buildings, or corridors beyond the compartment.
References: NFPA 13, Section 8.3.3.3.
NEW QUESTION # 30
......
Actual Questions Answers Pass With Real CHFM Exam Dumps: https://www.fast2test.com/CHFM-premium-file.html
CHFM Dumps Prepare Your Exam With 110 Questions: https://drive.google.com/open?id=1dqexy-c8TJnfnc9Z-vdEyU8CmSXtNSt3