NS0-176 PDF Dumps 2023 Exam Questions with Practice Test [Q25-Q48]

NS0-176 PDF Dumps 2023 Exam Questions with Practice Test

Dumps for Free NS0-176 Practice Exam Questions

NEW QUESTION 25
Which statement is true about NFS exports in Clustered Data ONTAP?

A. Export policies and rules need to be set at the data Vserver level and export policies are created and modified by editing /etc/exports on the node with the share.
B. Exports can be either persistent or temporary.
C. Exports can be either persistent or temporary, and export policies and rules need to be set at the data Vserver level.
D. Export policies are created and modified by editing /etc/exports on the node with the share.
E. Export policies and rules need to be set at the data Vserver level.

Answer: E

NEW QUESTION 26
Exhibit:

An administrator is building a FlexPod configuration with UCS 6296 Fabric Interconnect devices that support legacy Fibre Channel 9FC) connections. The administrator uses UCS Manager to configure the unified ports on the Fabric Interconnect.
Referring to the exhibit, how many ports will FC use after the configuration is completed?

A. 0
B. 1
C. 2
D. 3

Answer: A

NEW QUESTION 27
When configuring a volume to contain a LUN, which administrative tool automatically applies NetApp recommendations?

A. VMware vSphere
B. Data ONTAP command-line interface
C. OnCommand System Manager
D. Microsoft SystemCenter

Answer: C

NEW QUESTION 28
Your primary VSM needs to be edited, rebooted, or migrated. You need to initiate a manual switchover to your standby VSM.
What command will allow this to occur?

A. System standby
B. vsm switchover
C. Standby activate
D. System switchover

Answer: D

NEW QUESTION 29
Which three are types of Storage Virtual Machines? (Choose three.)

A. vFiler
B. data
C. node
D. intercluster
E. flex
F. cluster

Answer: B,C,F

NEW QUESTION 30
What is the maximum number of nodes that a NetApp SAN cluster supports?

A. 0
B. 1
C. 2
D. 3

Answer: D

NEW QUESTION 31
You have a FlexPod solution with Cisco 6296UP Fabric Interconnects. You currently have a direct-attached AFF8040 system using FCoE for storage connectivity. You would like to reconfigure the FlexPod so that the storage is connected through the upstream switches.
Using UCS Manager, which two steps would you perform to accomplish this task? (Choose two.)

A. Configure the FI ports with the Uplink role.
B. Using the Configure Unified Ports wizard, change the port types to FC.
C. Using the Configure Unified Ports wizard, change the port types to Ethernet.
D. Configure the FI ports with the FCoE Uplink role.

Answer: A,B

NEW QUESTION 32
When trying to configure a Virtual Port Channel (vPC), what might be a cause of the following error when trying to create the vPC domain?
Nexus-5548-B(config)# vpc domain 10
^% Invalid command at '^' marker.Nexus-5548-B(config)#

A. vPC domain cannot be configured at the global prompt
B. Have not yet turned on the vpc feature using the 'feature vpc' command
C. The vPC domain has already been configured
D. The vPC links have to be configured before the vPC domain can be added

Answer: B

NEW QUESTION 33
Which three management tools would you use to configure the NetApp storage component in a FlexPod Datacenter solution? (Choose three.)

A. Cisco UCS Central
B. NetApp OnCommand System Manager
C. NetApp OnCommand Perfromance Manager
D. Cisco UCS Director
E. NetApp Virtual Storage Console (VSC) for VMware Sphere

Answer: A,B,E

NEW QUESTION 34
You installed a new NetApp cluster running clustered Data ONTAP. There is a single Storage Virtual Machine (SVM) named esx1 on the cluster.
A volume named esx_datastore1 is created in the SVM esx1. The name of the root volume for the esx1 SVM is esx1_rootvol. The default export policy was applied to the volume esx1_rootvol.
You verified that the export policy applied to esx_datastore1 contains a single rule that allows all clients to mount the volume as read/write using any version of NFS. A Linux client attempts to NFS mount the volume and receives a Permission Denied error.
In this scenario, what caused this error?

A. UNIX permissions for the volume esx1_rootvol are not set to read/write.
B. The volume esx_datastore1 has not been mounted into the namespace of the esx1 SVM.
C. The default export-policy does not have at least one rule to allow all clients read-only access.
D. NFS has not been configured on the SVM esx1.

Answer: C

NEW QUESTION 35
You are attempting to establish a cluster peer relationship between two NetApp clusters, but the peering process fails.
What is a cause for this failure?

A. The cluster management LIF for the cluster cannot communicate with the cluster management LIF for the peer cluster.
B. The cluster LIFs on each node cannot communicate with the cluster LIFs on each node in the peer cluster.
C. The intercluster LIF on each node cannot communicate with the intercluster LIF on each node in the peer cluster.
D. The node management LIF on each node cannot communicate with the node management LIF on each node in the peer cluster.

Answer: C

NEW QUESTION 36
A customer wants to reuse existing networking equipment that was pulled from another data center for a new FlexPod Datacenter solution. They want to know if their switch models are supported.
In this scenario, which two switch models will accomplish this task? (Choose two.)

A. Cisco Catalyst 6504
B. Cisco Nexus 9396PX
C. Cisco Catalyst 9300-48P
D. Cisco MDS 9250i

Answer: B,D

NEW QUESTION 37
What is the correct flow control setting for the intercluster ports on a NetApp cluster?
to 50% cashback.

A. switched cluster = full switchless cluster = none
B. switched cluster = none switchless cluster = none
C. switched cluster = none switchless cluster = full
D. switched cluster = set to match the setting on switch port switchless cluster = none

Answer: D

NEW QUESTION 38
After deploying a FlexPod solution, which tool would you use to validate a successful installation?

A. Config Advisor
B. UCS Manager
C. System Manager
D. Hardware Universe

Answer: A

NEW QUESTION 39
A customer asks you to configure QoS on a Cisco Nexus 7000 Series switch within a FlexPod solution.
Which three steps are required to accomplish this task? (Choose three.)

A. Define traffic classes.
B. Perform a shut/no shut on the affected interfaces.
C. Attach policies to logical or physical interfaces and VLANs.
D. Associate policies and actions with each traffic class.
E. Attach policies to logical or physical interfaces and VSANs.

Answer: A,D,E

NEW QUESTION 40
A customer wants a newly deployed UCS C-Series server's fans to run at the minimum speed required to keep the server cool. The customer is also complaining that the server fans are making too much noise.
In this scenario, which type of fan speed should you select under the Power Control Policy of UCSM?

A. Max Power
B. Balanced
C. Performance
D. Low Power

Answer: B

NEW QUESTION 41
Refer to the exhibit.

Which is correct for configuring FCoE?

A. fcoe vlan 33int po11switchport trunk allowed vlan add 33vsan databasevsan 33
B. fcoe vsan 43int po21switchport trunk allowed vsan add 43vsan databasevsan 43
C. fcoe vsan 43int po11switchport trunk allowed vsan add 43vsan databasevsan 43
D. vlan 33fcoe vsan 43int po21switchport trunk allowed vsan add 43int vfc11bind interface po21vsan databasevsan 43 interface vfc 11
E. vlan 33fcoe vsan 43int po11switchport trunk allowed vlan add 33int vfc11bind interface po11switchport trunk allowed vsan 43vsan databasevsan 43 interface vfc11

Answer: E

NEW QUESTION 42
To support Storage Virtual Machines, which type of unique login account must be created?

A. vsadmin, for each Storage Virtual Machine
B. admin, for the cluster
C. admin, for each Storage Virtual Machine
D. vsadmin, for the cluster

Answer: A

NEW QUESTION 43
Which statement is true for Fibre Channel QoS System Class?

A. One can modify no-drop policy, and non FCoE traffic using natively the same class as FCoE will be remarked to 0
B. One cannot modify no-drop policy, and non FCoE traffic using natively the same class as FCoE will not be remarked
C. One cannot modify no-drop policy, and non FCoE traffic using natively the same class as FCoE will be remarked to 0
D. One can modify no-drop policy, and non FCoE traffic using natively the same class as FCoE will not be remarked

Answer: C

NEW QUESTION 44
Which set of commands maps VLAN 100 to VSAN 100?

A. Nexus 5000-A#configure terminal Nexus 5000-A (config) # vlan 100 Nexus 5000- A (config-vlan_ #fcoe vsan 100
B. Nexus 5000-A#configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-A (config)# vsan 100 Nexus 5000-A (config-vsan) # fcoe vsan 100
C. Nexus 5000-B# configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-B (config-vsan)# vsan 100 Nexus 5000-B(config- vsan) #vsan 100 name FCoE-VLAN 100
D. Nexus 5000-B# configure terminal Nexus 5000-B(config-vsan) # vlan 100 Nexus 5000-B (config-vsan)# vsan 100 name vsan100

Answer: A

NEW QUESTION 45
You are installing a FlexPod Express solution with a NetApp AFF A250 at a customer's remote site.
In this scenario, which two devices are required to provide an NFS v3 datastore? (Choose two.)

A. Cisco Nexus 3000 Switches
B. Cisco UCS 6454 Fabric Interconnects
C. NetApp BES-53248 Switches
D. Cisco UCS 6324 Fabric Interconnects

Answer: A,D

NEW QUESTION 46
Exhibit:

You just finished cabling a UCS 5108 chassis to the Fabric Interconnects.
Which diagram in the exhibit is cabled correctly according to the CVD guidelines?