[Sep 13, 2021] 300-625 Dumps Full Questions - Exam Study Guide [Q25-Q40]

[Sep 13, 2021] 300-625 Dumps Full Questions - Exam Study Guide

CCNP Data Center Free Certification Exam Material from Fast2test with 72 Questions

NEW QUESTION 25
Which configuration is available only in Cisco DCNM-SAN Advanced mode?

A. zoning
B. VMpath configuration
C. template-based provisioning
D. IVR

Answer: D

NEW QUESTION 26
Refer to the exhibit. A port channel has been configured between a Cisco MDS and a Cisco Fabric Interconnect switch. Which interface(s) in the port channel carry the control plane traffic?

A. from interface fc1/10
B. per packet, balanced between interfaces fc1/9 and fc1/10
C. per flow, balanced between interfaces fc1/9 and fc1/10
D. from interface fc1/9

Answer: C

NEW QUESTION 27
DRAG DROP
Drag and drop the DCNM configuration tasks from the left onto the correct tools on the right.
Select and Place:

Answer:

Explanation:

Section: Management and Monitoring

NEW QUESTION 28
A storage network engineer must install and configure a new MDS switch in a data center network. Which two statements about available choices during the MDS switch initial setup are correct? (Choose two.)

A. The engineer can choose what will be the administrator account.
B. The engineer can configure the default zone policy.
C. The engineer does not have the choice to enable or disable full zoneset distribution.
D. The engineer can configure the default switch port trunk mode.
E. The secure password standard is required.

Answer: A,B

NEW QUESTION 29
A storage administrator manually configures a storage switch to use a new static domain ID. After issuing an fcdomain restart vsan 1 command, the administrator sees that the switch is still using the existing domain ID.
What is the reason why the configuration is not working?

A. Build fabric notifications were not sent to the other switches.
B. Static domain IDs apply only after a switch is rebooted.
C. Domain manager fast restart is not enabled on the switch.
D. The disruptive keyword was not used on the command.

Answer: B

NEW QUESTION 30
A storage network engineer is upgrading a Cisco MDS Director with dual supervisor modules. The install command is executed on the standby supervisor module but fails. Which action would have prevented this failure?

A. Fabric Controller Service must be stopped before starting the upgrade.
B. Cisco Fabric Services must be disabled before starting the upgrade.
C. All FCoE interfaces configured on the MDS must be shut down before starting the upgrade.
D. The upgrade must be done on the active supervisor module only.

Answer: D

NEW QUESTION 31
Refer to the exhibit.

Refer to the exhibit. A user who is logged in as an operator cannot update the zoneset. What is the cause of this issue?

A. Hard zoning is enabled
B. Merge control is disabled
C. The fabric is locked by admin on another switch
D. The fabric is locked by admin on switch-2
E. The switch has a conflicting domain ID

Answer: C,E

NEW QUESTION 32
Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?

A. The rcf-reject option is enabled on the interfaces.
B. The autoreconfigure option is disabled on both switches.
C. The autoreconfigure option is enabled on both switches.
D. The rcf-reject option is disabled on the interfaces.

Answer: B

NEW QUESTION 33
Which result occurs when a VSAN is deleted that contains non-trunking ports?

A. The ports are moved to VSAN 4094.
B. The ports are removed from the configuration.
C. The port configurations are cleared.
D. The ports are moved to VSAN 1.

Answer: A

Explanation:
Section: Implementation

NEW QUESTION 34
Which statement about FCoE is true?

A. FCoE does not support NPV/NPIV mode.
B. Not a single FCoE VLAN can map to multiple VSANs.
C. FCoE is not supported on any Nexus 2000 Series Fabric Extenders.
D. Inter-switch FCoE links can be configured to carry multiple VSANs.

Answer: D

NEW QUESTION 35
Which result occurs if a device alias is renamed and then the original device alias name is used in an add command in the same session?

A. The rename command is moved to the rejected list and the add command executes successfully.
B. The device alias is renamed and the add command is moved to the rejected list.
C. Both commands execute successfully.
D. Both commands are moved to the rejected list.

Answer: C

Explanation:
Section: Implementation

NEW QUESTION 36
Which condition requires using a device alias rather than a Fibre Channel alias?

A. Aliases must be saved within a central database on the fabric
B. The zone database must be distributed over the fabric
C. All aliases being used are being configured in the same VSAN
D. The same alias must be used in zoning as well as DPVM

Answer: D

NEW QUESTION 37
Refer to the exhibit.

A storage network engineer gets remote access to two Cisco MDS 9000 Series Switches with an ISL trunk and receives several log messages. Which set of actions resolve the problem while least affecting service?

A. 1. Add :11:11:11:11:11:11:11:13 pwwn in zone Server11 and activate Zoneset10-A on MDS-A.
2. Remove VSAN 10 from the allowed VSAN range of interface fc1/11 on MDS-A and add it back in the range.
B. 1. Explicitly import zone set Zoneset10-A on MDS-B using the zoneset import interface import fc1/11 vsan 10 command.
2. Activate the zone set Zoneset10-A.
C. 1. Add :11:11:11:11:11:11:11:13 pwwn in zone Server11 and activate Zoneset10-A on MDS-A.
2. shut/no shut interface fc1/11 on MDS-A.
D. 1. Deactivate zone set Zoneset10-A on MDS-A.
2. shut/no shut interface fc1/11 on MDS-A.

Answer: C

Explanation:
Section: MDS Troubleshooting

NEW QUESTION 38
A storage administrator is configuring inter-VSAN routing on a fabric that contains duplicate domain IDs. Which feature must be configured to ensure continued operation?

A. IVR NAT
B. virtual domains
C. transit VSANs
D. auto topology

Answer: A

Explanation:
Section: Implementation

NEW QUESTION 39
After a subordinate switch requests a domain ID form a principal switch, the requested domain ID becomes the runtime domain ID, and all interfaces on the affected VSAN are isolated. What is a solution to the issue?