[Sep-2021] Pass HPE6-A45 Exam in First Attempt UpdatedHPE6-A45 Fast2test Exam Question
Aruba Certified Switching Professional (ACSP) V1 Dumps HPE6-A45 Exam for Full Questions - Exam Study Guide
NEW QUESTION 31
Refer to the exhibits.
Exhibit 1.
Exhibit 2.
The VoIP phone connects, authenticates successfully, and is dynamically assigned to tagged VLAN 6. The endpoint connected to the phone does not authenticate but starts to send untagged traffic.
How does the switch handle this traffic?
- A. It forwards the traffic in VLAN 6.
- B. It drops the traffic.
- C. It relays the traffic to the RADIUS server for authentication.
- D. It forwards the traffic in VLAN 5.
Answer: C
NEW QUESTION 32
Refer to the exhibit.
An AOS-Switch has the ACL shown in the exhibit. A network administrator then enters these commands:
Switch(config)# mac-access-list standard myACL
Switch(config-std-macl)# 25 deny 007d.45cc.0000 0000.0000.ffff
How does this ACL treat these frames:
1 = 007d.45cc.ffff 2 = 007d.45cc.0000
- A. It permits both frames.
- B. It denies frame 1 and permits frame 2.
- C. It denies both frames.
- D. It permits frame 1 and denies frame 2.
Answer: C
NEW QUESTION 33
A network administrator configures VSF settings on two Aruba 2930F switches. The switches form two separate VSF fabrics. What should the administrator check?
- A. that the switch with the lower priority has the lower member ID
- B. that each switch is assigned a unique VSF priority
- C. that the domain ID matches on both switches
- D. that LLDP MAD is configured on both members
Answer: C
NEW QUESTION 34
A network administrator configures DHCP snooping on VLAN 2. How does the switch handle DHCP traffic that arrives in this VLAN on an untrusted interface?
- A. It accepts packets from a DHCP server, but drops client packets.
- B. It accepts client packets, but drops packets from a DHCP server.
- C. It drops all DHCP traffic and logs a security event.
- D. It accepts both client and server packets as long as they match the DHCP binding table.
Answer: A
NEW QUESTION 35
Refer to the exhibit.
Switch-1 and Switch-2 are AOS-Switches, which are iBGP peers. ISP 1 and ISP 2 advertise some routes to the same Internet destinations. Switch-1 and Switch-2 must select between these routes based on AS path length.
What is required for Switch-1 and Switch-2?
- A. iBGP synchronization enabled
- B. eBGP and iBGP administrative distance set to the same value
- C. Multihop enabled for the connection to the iBGP neighbor
- D. ECMP disabled for BGP
Answer: B
NEW QUESTION 36
Which solution allows administrators to monitor link status and port utilization on AOS-Switches from a centralized location?
- A. Aruba Mobility Controller
- B. Aruba ClearPass
- C. Aruba AirWave
- D. Aruba Mobility Manager
Answer: C
NEW QUESTION 37
Refer to the exhibit.
Switch-1 is an AOS-switch that is operating at factory default settings for QoS and has type of service disabled. It receives a frame with 802.1p value 5 on trk1, on VLAN 2. How does the switch treat the frame when it forwards it on TRK2?
- A. It forwards it with normal priority and 802.1p 5
- B. It forwards it with higher than normal priority and 802.1p 0.
- C. It forwards it with higher than normal priority and 802.1p 5.
- D. It forwards it with normal priority and 802.1p 0.
Answer: D
NEW QUESTION 38
Two AOS-Switches connect on VLAN 10 in OSPF Area 1, which is defined as a stub area on both. Which mismatch can cause OSPF routers to lose adjacency?
- A. The administrator enables jumbo frames on VLAN 10 on just one of the routers.
- B. The administrator adds the no-summary option to Area 1 on just one of the routers.
- C. The administrator adds the backbone area to just one of the routers.
- D. The administrator enables graceful restart, or nonstop switching, on just one of the routers.
Answer: D
NEW QUESTION 39
A customer wants access layer switches that support routing, ACLs, backplane stacking, and Smart rate ports.
The customer asks about Aruba 5400R z 12 switches.
Which Aruba Switch model would better meet the customer's requirements?
- A. 0
- B. 1
- C. 2930F
- D. 2
Answer: B
Explanation:
Reference: https://www.arubanetworks.com/assets/so/SB_CampusSwitching.pdf
NEW QUESTION 40
Refer to the exhibit.
A known unicast packet is received from Switch-1 on the standby and must be forwarded to Switch-2. How does the VSF fabric decide which port in the aggregated link should forward the packet?
- A. The standby selects the port on the designated forwarder for the aggregation.
- B. The standby sends the packet to the commander over a VSF link, and the commander decides the correct port.
- C. The standby uses its own port in the link aggregation to forward the fabric.
- D. The standby uses the typical load sharing algorithm, and it might select either its port or the commander's port.
Answer: C
NEW QUESTION 41
Refer to the exhibit.
Both Switch-1 and Switch-2 redistribute RIP routes into OSPF. The network administrator wants routers in Area 1 to receive the redistributed routes from Switch-1 but not from Switch-2.
What should the administrator do to achieve this goal?
- A. Configure a subnet range for Area 1 on Switch-2, and set the no-advertise option.
- B. Configure Area 1 as a stub area, with no summaries on Switch-2.
- C. Configure Area 1 as a Not So Stubby Area (NSSA) on all routing devices in Area 1.
- D. Configure Area 1 as a stub area, and import the routes with a low metric on Switch-2.
Answer: C
NEW QUESTION 42
An AOS-Switch enforces 802.1X it receives an Access-Accept with this HPE VSA from its RADIUS server.
The switch then rejects the client. What is one requirement for the switch to accept the message and authorizes the client?
- A. The RADUS server settings must permit dynamic authorization
- B. The initial user role must be set to the factory default permit any role.
- C. User role authorization must be enabled globally on the switch.
- D. An aaa authentication local user group must have the contractor name.
Answer: B
NEW QUESTION 43
Refer to the exhibits.
Exhibit 1
Exhibit 2
Switch-1 has a power issue that causes it to fail. When Switch-1 comes back up, endpoints lose connectivity for a few minutes. The network administrator decides to enter this command on Switch-1:
Switch-1 (config)# vlan 10 vrrp vrid 10 preempt-delay-time 120
Exhibit 2 shows the VRRP configuration just after the change. What is the effect of this change?
- A. Switch-1 now waits to take over as Master if it fails and recovers. This should prevent the connectivity issue from occurring again.
- B. Switch-1 experiences an internal error in the VRRP process. This error causes Switch-2 to take over as Master for VLAN 2.
- C. Switch-1 and Switch-2 both become Master in their own VRRP virtual router due to the delay timer mismatch. The mismatch must be fixed.
- D. Switch-1 continues to act as it did before the preempt delay time was set. Administrators must plan additional changes to fix the issue.
Answer: B
NEW QUESTION 44
Refer to the exhibits.
Exhibit 1
Exhibit 2
A company does not require authentication for security, but AOS-Switches are set up to use local MAC authentication (LMA) to assign the correct VLAN and priority to IP phones. IP phones and computers belong to different VLANs. Each device is supposed to connect to a specific port, but sometimes users connect their devices to the wrong ports and cannot receive access without help from IT.
How can a network administrator configure the switches to eliminate this issue?
- A. Apply LMA to all edge switch ports, and set the unauth VLAN to the user VLAN.
- B. Create a user role that applies the user VLAN, and set this role as the initial role.
- C. Set the address limit to 2 on the switch ports that apply LMA.
- D. Add the MAC addresses for computers to the myPhones MAC group.
Answer: A
Explanation:
Explanation
If you place the computer's MAC in that group, all traffic from the computer will get placed in the same class as the IP phones, which is not a good practice (Although it will technically work). (The only reason they are using LMA is the dynamically assign a VLAN/QoS priority to that device)
NEW QUESTION 45
AOS-Switches authenticate guests to ClearPass with captive portal. An administrator notices that some guests are unable to reach the captive portal page. What will resolves this issue?
- A. Permit Allow All MAC-Auth on the ClearPass Portal.
- B. Permit DNS on the ClearPass Portal.
- C. Permit HTTP or HTTPS on the ClearPass Portal.
- D. Permit DHCP on the ClearPass Portal.
Answer: C
NEW QUESTION 46
Refer to the exhibits.
Exhibit 1
Exhibit 2
Exhibit 2 shows IGMP groups on Switch-2, which runs IGMP but not PIM. Switch-1 and Switch-3 do not have IGMP or PIM enabled. Client 1 begins to forward multicasts to 239.1.1.1.
Which clients receive the multicasts?
- A. Client 2, Client 3, and Client 4
- B. Client 3 and Client 4, but not Client 2
- C. Client 3, but not any of the other clients
- D. Client 2, but not any of the other clients
Answer: D
NEW QUESTION 47
Refer to the exhibit.
A network administrator sets up 802.1X authentication to a RADIUS server on an AOS-Switch. The RADIUS server and user devices are both set up to use PEAP MSCHAPv2. The administrator tests the authentication and sees the output shown in the exhibit. Which issue could cause this output?
- A. The switch port is set for user mode 802.1X, but the RADIUS server is set for port mode
- B. The administrator entered the wrong password for the test account
- C. The RADIUS shared secret does not match on the switch and the server
- D. The switch does not have a certificate for port-access installed on the switch
Answer: C
NEW QUESTION 48
Refer to the exhibits.
The network administrator enters the commands shown in Exhibit 2, and Switch-1 and Switch-2 exchange keepalive messages. What is the expected behavior if Switch-1 later fails to receive keepalive messages from Switch-2?
- A. After two consecutive missed keep-alive packets, Switch-1 sends SNMP traps, and Link 1 stays up until the issue is fixed.
- B. Switch-1 disables interface 1 for 10 seconds, and then re-enables it. The same process repeats twice.
If the issue persists, the switch disables the interface permanently. - C. Switch-1 disables interface 1 for 10 seconds and then re-enables it. The interface continues to be re- enabled and disabled every 10 seconds until the issue is fixed.
- D. After two consecutive missed keep-alive packets, Switch-1 disables interface 1, and the interface stays disabled until the issue is fixed.
Answer: D
NEW QUESTION 49
Refer to the exhibit.
Switch-1 runs BGP. What should the network administrator do to permit Switch-1 to establish a neighbor relationship with Router-1?
- A. Set the BGP AS number to 46501.
- B. Enable BGP on VLAN 100.
- C. Specify 192.168.1.0/30 with the network command in the BGP context.
- D. Configure 192.168.1.2 as a neighbor manually within the BGP context.
Answer: D
NEW QUESTION 50
......
Authentic Best resources for HPE6-A45 Online Practice Exam: https://www.fast2test.com/HPE6-A45-premium-file.html