[UPDATED 2023] HP HPE6-A73 Questions Prepare with Free Demo of PDF
NEW 2023 Certification Sample Questions HPE6-A73 Dumps & Practice Exam
HP HPE6-A73 (Aruba Certified Switching Professional) certification exam is designed for individuals who aim to validate their skills and knowledge in configuring and managing complex switched networks using ArubaOS-Switches. Aruba, a Hewlett Packard Enterprise company, provides a range of networking solutions, and the HPE6-A73 certification exam focuses specifically on their switching technology. Aruba Certified Switching Professional Exam certification exam validates the skills and knowledge required to design, configure, implement, and troubleshoot modern switched networks using ArubaOS-Switches.
NEW QUESTION # 28
An administrator is supporting a network with the access layer consisting of AOS-CX 6300 and 6400 switches. The administrator needs to quickly deploy Aruba IAPs and security cameras in the network, ensuring that the correct QoS and VLAN settings are dynamically applied to the switch ports. Currently, switches are not configured to do device authentication, and no authentication server exists in the network.
Which AOS-CX feature should the administrator use to dynamically assign the policy settings to the correct switch ports?
- A. Dynamic segmentation
- B. Device profiles
- C. Voice VLANs
- D. Change of authorization
Answer: A
NEW QUESTION # 29
An administrator of a company has concerns about upgrading the access layer switches. The users rely heavily on wireless and VoIP telephony. Which is the best recommendation to ensure a short downtime for the users during upgrading the access layer switches?
- A. Implement VSX on the AOS-CX access switches
- B. Install AOS-CX 6300 or 6400 switches with always-on POE
- C. Install the in-service software upgrade (ISSU) feature with clustering enabled
- D. Implement VSF on the AOS-CX access switches
Answer: B
Explanation:
The key is to reduce the impact. VSF or not will have same impact when the switch reboots. But if the switch support always on poe then at least the POE clients will be ready before the switch finish booting up. If you dont have always on POE, then the poe clients will reboot AFTER the switch boots up.
NEW QUESTION # 30
A network administrator is tasked to set up BGP in the company's network. The administrator is defining an eBGP peering between an AOS-CX switch and a directly-connected service provider. The administrator has configured the following on the AOS-CX switch:
However, when using the "show bgp all summary" command, the state does not display "Established" for the eBGP peer. What must the administrator configure to fix this issue?
- A. router bgp 64500 enable
- B. router bgp 64500 address-family ipv4 unicast neighbor 192.168.1.1 activate
- C. router bgp 64500 neighbor 192.168.1.1 update-source loopback0
- D. router bgp 64500 neighbor 192.168.1.1 ebgp-multihop
Answer: B
NEW QUESTION # 31
A network has an ABR that connects area 0 and 1. A network engineer configures a summarized route for area 0. The ABR is a designated router (DR) for the segment it uses to connect to area 1.
Which LSA type is assigned to this route when the summarized route is advertised into area 1 by the ABR?
- A. LSA2
- B. LSA1
- C. LSA3
- D. LSA4
Answer: D
NEW QUESTION # 32
An AOS-CX switch is configured to implement downloadable user roles. Examine the AOS-CX switch output:
Based on this output, what is the state of the user's access?
- A. MAC authentication has passed, but 802.1X authentication is in progress
- B. The RADIUS request timed out to the AAA server
- C. No downloadable user role exists
- D. The port should be configured for 802.1X
Answer: D
NEW QUESTION # 33
Examine the attached exhibit.
The network administrator it trying to add a remote location as area 3 to the network shown in the diagram.
Based on Current connection restrictions, the administrator cannot connect area 3 directly to area 0. The network is using AOS-CX switches.
Which feature should the administrator implement to provide connectivity to the remote location?
- A. Bidirectional forward detection (BFD
- B. Not-so-study areas
- C. OSPFv3
- D. Virtual links
Answer: D
NEW QUESTION # 34
An administrator is implementing a downloadable user role solution involving AOS-CX switches. The AAA solution and the AOS-CX switches can successfully authenticate users; however, the role information fails to download to the switches. What policy should be added to an intermediate firewall to allow the downloadable role function to succeed?
- A. Allow UDP 8211
- B. Allow TCP 443
- C. Allow TCP 22
- D. Allow UDP 1811
Answer: A
NEW QUESTION # 35
An AOS-CX switch is configured to implement downloadable user roles. Examine the AOS-CX switch output:
Based on this output, what is the state of the user's access?
- A. MAC authentication has passed, but 802.1X authentication is in progress
- B. The RADIUS request timed out to the AAA server
- C. No downloadable user role exists
- D. The port should be configured for 802.1X
Answer: D
NEW QUESTION # 36
Which protocol does NetEdit use to discover devices in a subnet during the discovery process?
- A. LLDP
- B. ARP
- C. DHCP
- D. ICMP
Answer: A
NEW QUESTION # 37
Examine the AOS-CS switch output:
Based on this output, what is correct?
- A. 802.1X authentication occurred and downloadable user roles are deployed
- B. 802.1X authentication was successful, but MAC authentication is yet to start
- C. Only 802.1X authentication is configured on the port
- D. A local user role was deployed using a ClearPass solution
Answer: A
NEW QUESTION # 38
Examine the network topology.
The network is configured for OSPF with the following attributes:
Here is the OSPF configuration performed on Core1:
Based on the above information, what is correct?
- A. Area 1 has 23 routes
- B. Corel has received one type 5 LSA from the ASBR.
- C. Area 0 has 81 routes
- D. ISP 1 is not reachable from any area.
Answer: C
NEW QUESTION # 39
What is correct regarding the operation of VSX and multicasting with PIM-SM routing configured?
- A. Each VSX peers runs PIM and creates a shared group database. Both VSX peers can forward multicast streams to receivers in a VLAN, achieving load sharing
- B. Each VSX peers runs PIM and builds its own group database. Both VSX peers can forward multicast streams to receivers in a VLAN, achieving load sharing
- C. Each VSX peers runs PIM and builds its own group database. One of the VSX peers is elected as the designated router (DR) to forward multicast streams to a receiver VLAN
- D. Each VSX peers runs PIM and creates a shared group database. One of the VSX peers is elected as the designated router (DR) to forward multicast streams to a receiver VLAN
Answer: C
Explanation:
"both VSX switches as a PIM Designate Router (DR). One node is the actual DR, the other node is the proxy DR." "Only the actual DR performs multicast routing and forward traffic destined to groups to its downstream VLANs in the data-path." https://www.arubanetworks.com/techdocs/AOS-CX/10.07/HTML/5200-7888/Content/Chp_Pre_tra_loss/ip-mul-rou-10.htm
NEW QUESTION # 40
What is correct regarding the operation of VSX and multicasting with PIM-SM routing configured?
- A. Each VSX peers runs PIM and builds its own group database. Both VSX peers can forward multicast streams to receivers in a VLAN, achieving load sharing
- B. Each VSX peers runs PIM and builds its own group database. One of the VSX peers is elected as the designated router (DR) to forward multicast streams to a receiver VLAN
- C. Each VSX peers runs PIM and creates a shared group database. Both VSX peers can forward multicast streams to receivers in a VLAN, achieving load sharing
- D. Each VSX peers runs PIM and creates a shared group database. One of the VSX peers is elected as the designated router (DR) to forward multicast streams to a receiver VLAN
Answer: C
NEW QUESTION # 41
Examine the attached diagram
Two AOS-CX switches are configured for VSX at the access layer, where servers attached to them. An SVI interface is configured for VLAN 10 and serves as the default gateway for VLAN 10. The ISL link between the switches fails, but the keepalive interface functions. Active gateway has been configured on the switches.
What is correct about access from the servers to the Core?
- A. Server 2 can successfully access the core layer via the keepalive link.
- B. Server 1 can access the core layer via both uplinks.
- C. Server 2 cannot access the core layer.
- D. Server 1 and Server 2 can communicate with each other via the core layer.
Answer: B
NEW QUESTION # 42
A network administrator wants to centralize the management of AOS-CX switches by implementing NetEdit How should theadministrator purchase and/or install the NetEdit solution?
- A. Installed in a virtualized solution by usung the Aruba-supplied OVA file
- B. Install as a hardware appliance
- C. Installed on a supported version of Debian Linux
- D. Installed on a supported version of RedHat Enterprise Linux
Answer: A
NEW QUESTION # 43
What are best practices when implementing VSX on AOS-CX switches? (Choose two.)
- A. Timers should be left at their default values.
- B. The ISL lag should use the default MTU size.
- C. The ISL lag should use at least 10GbE links or faster.
- D. The default system MAC addresses should be used.
- E. The keepalive connection should use a direct layer-3 connection.
Answer: A,E
NEW QUESTION # 44
What is correct regarding rate limiting and egress queue shaping on AOS-CX switches?
- A. Rate limiting and egress queue shaping can be used to restrict inbound traffic
- B. Only a traffic rate and burst size can be defined for a queue
- C. Limits can be defined only for broadcast and multicast traffic
- D. Rate limiting and egress queue shaping can be applied globally
Answer: B
Explanation:
you could apply egress queue shaping to the high priority queues to prevent starvation of low priority queues. Egress queue shaping allows you to apply a maximum bandwidth to a priority queue, as well as a burst size. The port buffers excess traffic up to the burst size and sends the buffered traffic at the max rate, smoothing out bursts while also preventing the high priority queue from exceeding its maximum rate and starving out lower priority queues.
NEW QUESTION # 45
What is correct regarding multicasting and AOS-CX switches?
- A. IGMP snooping is disabled, by default on Layer-2 VLAN interfaces
- B. IGMP query- functions are enabled by default , on Layer-2 VLAN interfaces
- C. IGMP snooping is enabled by default , on Layer-3 VLAN interfaces
- D. IGMP-enabled AOS-CX switches flood unknown multicast destinations.
Answer: A
NEW QUESTION # 46
The AOS-CX mobile app allows a network engineer or technician to perform which tasks? (Choose two.)
- A. Use NetEdit to manage switch configuration.
- B. Schedule an operating system upgrade.
- C. Create a stack of AOS-CX switches.
- D. Transfer files between the switch and your mobile device.
- E. Securely access the switch using SSH.
Answer: C,D
Explanation:
ACSP Study Guide Page 66 - Key Features (Transfer files between the switch and your mobile device)
NEW QUESTION # 47
A network administrator is implementing NAE on AOS-CX switches. When attempting to create an agent on a particular switch, the agent appears in the NAE Agents panel with a red triangle error symbol and a status of
"Unknown".
What is the cause of this issue?
- A. The number of scripts or agents has exceeded the hardware's capabilities
- B. A connectivity issue exists between NAE and the AOS-CX switch
- C. The RESTful API has not been enabled on the AOS-CX switch
- D. The administrator does not have the appropriate credentials to interact with NAE
Answer: B
NEW QUESTION # 48
What is the correct way of associating a VRF instance to either a VLAN or an interface?
- A. Switch(config)# vlan <VLAN-ID>
Switch(config-vlan-<VLAN-ID># vrf attach < vrf-name > - B. Switch(config)# vlan <VLAN-ID> vrf attach < vrf-name >
- C. Switch(config)# interface <interface-ID>
Switch(config-if)# vlan access <VLAN-ID> vrf attach <vrf-name> - D. Switch(config)# vlan <VLAN-ID> vrf < vrf-name >
Answer: A
NEW QUESTION # 49
......
HP HPE6-A73 exam covers a wide range of topics, including ArubaOS-Switches fundamental concepts, VLANs, Spanning Tree Protocol (STP), and Link Aggregation Control Protocol (LACP). HPE6-A73 exam also covers advanced switching concepts such as Virtual Switching Framework (VSF), Multi-Chassis Link Aggregation Group (MC-LAG), and Quality of Service (QoS). Candidates are required to have a deep understanding of Aruba Switching and Routing technologies, as well as the ability to configure and troubleshoot complex switching solutions.
HPE6-A73 Deluxe Study Guide with Online Test Engine: https://www.fast2test.com/HPE6-A73-premium-file.html
HPE6-A73 Test Prep Training Practice Exam Questions Practice Tests: https://drive.google.com/open?id=12XFTY8nD3vqZuKkQ4vLi1Aayz4IT8zrm