[Aug 16, 2023] Fully Updated Dumps PDF - Latest 300-615 Exam Questions and Answers
100% Free 300-615 Exam Dumps to Pass Exam Easily from Fast2test
NEW QUESTION # 87
Refer to the exhibit.
vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)
- A. Match vPC domain ID between the two devices.
- B. Configure vPC peer link and vPC peer keepalive correctly.
- C. Activate VLANs on the vPC.
- D. Configure IP address on the interface.
- E. Configure one of the switches as primary for the vPC.
Answer: A,C
NEW QUESTION # 88
A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?
- A. Set the same WWPN pools for vHBA adapters
- B. Set the boot LUN to the lowest LUN ID in the storage array
- C. Set the boot LUN to the highest LUN ID in the storage array
- D. Set the same WWNN pools for vHBA adaptor
Answer: B
NEW QUESTION # 89
An engineer is troubleshooting issues in Cisco UCS Director. Drag and drop the possible causes from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION # 90
An engineer must configure Linux hosts that are deployed on Cisco UCS B-Series Servers to boot from SAN. The SAN boot policy is configured in Cisco UCS Manager, and the boot order is verified to be set as expected However, the Linux hosts fail to boot. Which action resolves the issue?
- A. Delete and reconfigure the boot LUN
- B. Remove all of the local storage that is installed
- C. Delete and reconfigure the pWWN of the SAN boot target
- D. Remove all of the ISO images that are mounted as a virtual CD-ROM
Answer: B
NEW QUESTION # 91
One of Cisco Nexus Series interfaces has become errdisabled with the error message "DCX-No ACK in 100 PDUs". What is the cause of this error?
- A. The acknowledgement number in the server response has not incremented for 100 exchanges.
- B. The host has not responded to the Control Sub-TLV DCBX exchanges of the switch.
- C. LLDP is disabled on the switch.
- D. Cisco Discovery Protocol is disabled on the switch.
Answer: B
NEW QUESTION # 92
Refer to the exhibit.
A web browser displays a "not secure" warning message when accessing the web interface of Cisco UCS Manager. Which action resolves the issue?
- A. Use the correct TCP port for HTTPS.
- B. Load third-party certificate to UCS Manager.
- C. Use a supported version of UCS Manager.
- D. Use a supported web browser.
Answer: B
NEW QUESTION # 93
A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered, has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment. Which action resolves the problem?
- A. Modify the ISIS interface peering IP address between apic 1 and Leaf-1
- B. Clean reload the Leaf-1 switch
- C. Define the new TEP address for Leaf-1
- D. Change the clock offset from low to high between apic 1 and Leaf-1
Answer: C
NEW QUESTION # 94
Refer to the exhibit.
An attempt to bind the Ethernet interface to vFC fails. Which action resolves the issue?
- A. Configure the interface as a trunk port.
- B. Add the FCoE VLAN to the allowed VLAN list.
- C. Configure the interface to use the native VLAN of the trunk port.
- D. Configure the FCoE VLAN that corresponds to the vFC VSAN as a private VLAN.
Answer: A
NEW QUESTION # 95
The external routes fail to propagate to leaf switches in Cisco ACI fabric. Which two actions resolve the issue?
(Choose two.)
- A. Associate the correct contract to the L3Out.
- B. Configure an MP-BGP area.
- C. Assign an MP-BGP AS number to the fabric.
- D. Specify the spine nodes as route reflectors.
- E. Enable the VTEP pool in the fabric.
Answer: C,D
Explanation:
Section: Network
NEW QUESTION # 96
Refer to the exhibit.
A network engineer needs to capture traffic from the VMs that utilize the IOM host interface Eth1/1/23 of a Cisco UCS B-Series chassis. A traffic analyzer is used to get traffic captured from the Eth1/4 interface of the subordinate fabric interconnect. The network engineer notices that traffic is not captured on the traffic analyzer. Which action resolves the issue?
- A. Span the traffic from the Eth 1/4 of the primary fabric interconnect.
- B. Span the traffic from the Eth 1/2 of the subordinate fabric interconnect.
- C. Span the traffic from the Eth 1/4 of the subordinate fabric interconnect.
- D. Span the traffic from the Eth 1/2 of the primary fabric interconnect.
Answer: A
NEW QUESTION # 97
Refer to the exhibit.
During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.
- A. Reconfigure the Drive Type from "Removable" to "Non-Removable"
- B. Configure the RAID that is associated with the card.
- C. Set SLOT-1 Sync Mode to "Auto"
- D. Insert an SD card into SLOT-2
Answer: A
NEW QUESTION # 98
Refer to the exhibit.
A Postman call to a Cisco APIC fails. The access credentials were confirmed to be configured as expected.
Which action resolves the issue?
- A. Modify the target protocol type to XML
- B. Change the IP address to a domain name
- C. Modify the protocol to HTTP
- D. Change operation type to POST
Answer: D
NEW QUESTION # 99
Refer to the Exhibit.
An Engineer cannot log in to the Cisco IMC page of the Cisco UCS C220 server. Which action resolve the issue?
- A. Replace the self-signed certificate that is installed on the Cisco IMC with a server certificate that is signed from the client corporate certificate.
- B. Replace the self-signed certificate that is installed on the Cisco IMC with a user certificate that is signed from the client corporate certificate.
- C. Use the DNS of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.
- D. Se the FQDN of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.
Answer: A
NEW QUESTION # 100
Refer to the exhibit.
Partial configuration from N9K-1 and N9K-2 is included. The client has two WANs connected.
* WAN-1 is for normal business-day activities.
* WAN-2 is for server backups during nonworking hours of 1:00 a.m. to 5:00 a.m. daily.
The client says that at the scheduled time for backup, the data center server failed to use the WAN-2 link to back up the servers to the cloud backup system. What is the solution to this problem?
- A. The Cron entry must be configured without double quotes.
- B. The applet called "Backup" must include an action to remove the current static route.
- C. The Cisco Nexus switch must be configured with one applet because a configuration with two applets will fail.
- D. The event timer must be written in epoch time format.
Answer: B
NEW QUESTION # 101
Refer to the exhibit.
A recent configuration change removes the HSRP adjacency between the SW-1 and SW-2 Cisco Nexus switches. The change causes the servers on this subnet to lose Internet access. Which action restores the connectivity of all servers on VLAN 13?
- A. Set the HSRP password on SW-2.
- B. Disable HSRP IP redirects on SW-1.
- C. Activate HSRP preempt on SW-2.
- D. Set the HSRP priority to 70 on SW-1.
Answer: C
NEW QUESTION # 102
Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION # 103
Drag and drop the commands from the left onto the correct categories on the right.
Answer:
Explanation:
NEW QUESTION # 104 
Refer to the exhibit. vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)
- A. Match vPC domain ID between the two devices.
- B. Configure vPC peer link and vPC peer keepalive correctly.
- C. Activate VLANs on the vPC.
- D. Configure IP address on the interface.
- E. Configure one of the switches as primary for the vPC.
Answer: A,C
Explanation:
Section: Network
NEW QUESTION # 105
A request to activate the port security database is rejected. Which action do you perform to investigate the cause of the issue?
- A. Verify that devices are fully attached to the active database.
- B. Find conflicting entries between the active and configuration databases.
- C. Use the force option to identify rejected devices.
- D. Enable the auto-learning feature.
Answer: C
Explanation:
Section: Management and Operations
NEW QUESTION # 106
......
Free 300-615 Exam Questions 300-615 Actual Free Exam Questions: https://www.fast2test.com/300-615-premium-file.html
Verified 300-615 dumps and 169 unique questions: https://drive.google.com/open?id=1k2g-3EvXtRCWSSEJWw0SCqz7hEgR89ru