New NSE7_LED-7.0 Dumps For Preparing NSE 7 Network Security Architect Certified Fortinet Exam Well
Updated NSE7_LED-7.0 Dumps Questions Are Available [2024] For Passing Fortinet Exam
NEW QUESTION # 21
You are setting up an SSID (VAP) to perform RADIUS-authenticated dynamic VLAN allocation.
Which three RADIUS attributes must be supplied by the RADIUS server to enable successful VLAN allocation? (Choose three.)
- A. Tunnel-Pvt-Group-ID
- B. Tunnel-Medium-Type
- C. Tunnel-Private-Group-ID
- D. Tunnel-Type
- E. Tunnel-Preference
Answer: A,B,D
NEW QUESTION # 22
Refer to the exhibit.
Examine the FortiSwitch security policy shown in the exhibit
If the security profile shown in the exhibit is assigned to all ports on a FortiSwitch device for 802 1X authentication which statement about the switch is correct?
- A. All EAP messages will be terminated on FortiSwitch
- B. FortiSwitch will assign non-802 1X devices to the onboarding VLAN
- C. FortiSwitch will try to authenticate non-802 1X devices using the device MAC address as the username and password
- D. FortiSwitch cannot authenticate multiple devices connected to the same port
Answer: B
Explanation:
Explanation
According to the FortiSwitch Administration Guide, "If a device does not support 802.1X authentication, you can configure the switch to assign the device to an onboarding VLAN. The onboarding VLAN is a separate VLAN that you can use to provide limited network access to non-802.1X devices." Therefore, option C is true because it describes the behavior of FortiSwitch when the security profile shown in the exhibit is assigned to all ports. Option A is false because FortiSwitch can authenticate multiple devices connected to the same port using MAC-based or MAB-EAP modes. Option B is false because FortiSwitch will not try to authenticate non-802.1X devices using the device MAC address as the username and password, but rather use MAC authentication bypass (MAB) or EAP pass-through modes. Option D is false because all EAP messages will be terminated on FortiGate, not FortiSwitch, when using 802.1X authentication.
NEW QUESTION # 23
Refer to the exhibit.
Examine the debug output shown in the exhibit
Which two statements about the RADIUS debug output are true'' (Choose two)
- A. The user student belongs to the SSLVPN group
- B. User authentication failed
- C. User authentication succeeded using MSCHAP
- D. The RADIUS server sent a vendor-specific attribute in the RADIUS response
Answer: A,C
Explanation:
Explanation
According to the exhibit, the debug output shows a RADIUS debug output from FortiGate. The output shows that FortiGate sent a RADIUS Access-Request packet to FortiAuthenticator with the username student and received a RADIUS Access-Accept packet from FortiAuthenticator with a Class attribute containing SSLVPN.
Therefore, option A is true because it indicates that the user student belongs to the SSLVPN group on FortiAuthenticator. The output also shows that FortiGate used MSCHAP as the authentication method and received a MS-MPPE-Send-Key and a MS-MPPE-Recv-Key from FortiAuthenticator. Therefore, option D is true because it indicates that user authentication succeeded using MSCHAP. Option B is false because user authentication did not fail, but rather succeeded. Option C is false because FortiAuthenticator did not send a vendor-specific attribute in the RADIUS response, but rather standard attributes defined by RFCs.
NEW QUESTION # 24
You are investigating a report of poor wireless performance in a network that you manage. The issue is related to an AP interface in the 5 GHz range. You are monitoring the channel utilization over time.
What is the recommended maximum utilization value that an interface should not exceed?
- A. 85%
- B. 65%
- C. 95%
- D. 75%
Answer: D
Explanation:
NEW QUESTION # 25
An administrator has configured an SSID in bridge mode for corporate employees. All APs are online and provisioned using default AP profiles. Employees are unable to locate the SSID to connect.
Which two configurations can the administrator verify? (Choose two.)
- A. Verify that the Block Intra-SSID Traffic (intra-vap-privacy) option in the SSID configuration is disabled
- B. Verify that the broadcast SSID option is enabled in the SSID configuration
- C. Verify that the SSID to an AP group that should be broadcasting the SSID is applied
- D. Verify that the SSID is manually applied on AP profiles for both 2.4 GHz and 5 GHz radios
Answer: B,D
Explanation:
https://community.fortinet.com/t5/FortiGate/Technical-Tip-How-to-enable-and-disable-broadcast- of-SSID/ta-p/191840
NEW QUESTION # 26
Which two statements about MAC address quarantine by redirect mode are true? (Choose two)
- A. The quarantined device is moved to the quarantine VLAN
- B. The device MACaddress is added to the Quarantined Devices firewall address group
- C. It is the default mode for MAC address quarantine
- D. The quarantined device is kept in the current VLAN
Answer: B,D
Explanation:
Explanation
According to the FortiGate Administration Guide, "MAC address quarantine by redirect mode allows you to quarantine devices by adding their MAC addresses to a firewall address group called Quarantined Devices.
The quarantined devices are kept in their current VLANs, but their traffic is redirected to a quarantine portal." Therefore, options B and D are true because they describe the statements about MAC address quarantine by redirect mode. Option A is false because the quarantined device is not moved to the quarantine VLAN, but rather kept in the current VLAN. Option C is false because redirect mode is not the default mode for MAC address quarantine, but rather an alternative mode that can be enabled by setting mac-quarantine-mode to redirect.
https://docs.fortinet.com/document/fortiap/7.0.0/configuration-guide/734537/radius-authenticated-dynamic-vlan-: https://docs.fortinet.com/document/fortigate/7.0.0/administration-guide/734537/mac-address-quarantine
NEW QUESTION # 27
Refer to the exhibit. Examine the IPsec VPN phase 1 configuration shown in the exhibit. An administrator wants to use certificate-based authentication for an IPsec VPN user.
Which three configuration changes must you make on FortiGate to perform certificate-based authentication for the IPsec VPN user? (Choose three)
- A. In the IKE section of the IPsec VPN tunnel in the Mode field select Main (ID protection)
- B. Create a PKI user for the IPsec VPN user, and then configure the IPsec VPN tunnel to accept the PKI user as peer certificate
- C. Import the CA that signed the user certificate
- D. In the Authentication section of the IPsec VPN tunnel in the Method drop-down list select Signature and then select the certificate that FortiGate will use for IPsec VPN
- E. Enable XAUTH on the IPsec VPN tunnel
Answer: B,C,D
NEW QUESTION # 28
An administrator is testing the connectivity for a new VLAN. The devices in the VLAN are connected to a FortiSwitch device that is managed by FortiGate. Quarantine is disabled on FortiGate.
While testing, the administrator noticed that devices can ping FortiGate and FortiGate can ping the devices. The administrator also noticed that inter-VLAN communication works. However, intra-VLAN communication does not work.
Which scenario is likely to cause this issue?
- A. The FortiSwitch MAC address table is missing entries
- B. The FortiGate ARP table is missing entries
- C. Access VLAN is enabled on the VLAN
- D. The native VLAN configured on the ports is incorrect
Answer: C
NEW QUESTION # 29
Which two statements about the guest portal on FortiAuthenticator are true? (Choose two.)
- A. Each remote user on FortiAuthenticator can sponsor up to 10 guest accounts
- B. Administrators must approve all guest accounts before they can be used
- C. Administrators can use one or more incoming parameters to configure a mapping rule for the guest portal
- D. The guest portal provides pre and post-log in services
Answer: C,D
Explanation:
The guest portal on FortiAuthenticator can offer services both before and after a guest logs in, such as displaying terms of use before login and providing access to network resources after successful authentication.
Administrators have the ability to configure mapping rules for the guest portal using various incoming parameters. This allows for flexible and dynamic handling of guest account creation and access permissions based on different criteria.
NEW QUESTION # 30
You are configuring a FortiGate wireless network to support automated wireless client quarantine using IOC Which two configurations must you put in place for a wireless client to be quarantined successfully? (Choose two)
- A. Configure a firewall policy to allow communication
- B. Configure the wireless network to be in bridge mode
- C. Configure the wireless network to be in tunnel mode
- D. Configure the FortiGate device in the Security Fabric with a FortiAnalyzer device
Answer: C,D
Explanation:
Explanation
According to the FortiGate Administration Guide, "To enable automated wireless client quarantine using IOC, you must configure the following settings: Configure your wireless network to be in tunnel mode. This allows FortiGate to inspect all wireless traffic and applysecurity policies. Configure your FortiGate device in the Security Fabric with a FortiAnalyzer device. This allows FortiAnalyzer to detect indicators of compromise (IOC) from wireless traffic and send quarantine commands to FortiGate." Therefore, options A and B are true because they describe the configurations that must be put in place for a wireless client to be quarantined successfully using IOC. Option C is false because configuring a firewall policy to allow communication is not required, as the default firewall policy for tunnel mode wireless networks is to allow all traffic. Option D is false because configuring the wireless network to be in bridge mode is not supported, as FortiGate cannot inspect or quarantine wireless traffic in bridge mode.
NEW QUESTION # 31
An administrator has configured an SSID in bridge mode for corporate employees All APs are online and provisioned using default AP profiles Employees are unable to locate the SSID to conned Which two configurations can the administrator verify? (Choose two)
- A. Verify that the Block Intra-SSID Traffic (intra-vap-privacy) option in the SSID configuration is disabled
- B. Verify that the SSID is manually applied on AP profiles for both 2 4 GHz and 5 GHz radios
- C. Verify that the broadcast SSID option is enabled in the SSID configuration
- D. Verify that the SSID to an AP group that should be broadcasting the SSID is applied
Answer: C,D
Explanation:
Explanation
According to the FortiAP Configuration Guide1, "To enable the SSID, you must select at least one channel for the radio. If no channels are selected, the SSID will not be enabled. You must also enable Broadcast SSID." Therefore, option A is true because the broadcast SSID option allows the SSID to be visible to wireless clients.
Option C is also true because the SSID must be applied to an AP group that contains the APs that should be broadcasting the SSID. According to the same guide1, "You can create AP groups and assign them to different locations or departments. You can then apply different settings, such as SSIDs, to each group." Option B is false because blocking intra-SSID traffic prevents wireless clients on the same SSID from communicating with each other, which is not related to broadcasting the SSID. Option D is false because the SSID can be applied to an AP group or a global profile, which will automatically apply to all APs, without manually configuring each AP profile.
NEW QUESTION # 32
Which two pieces of information can the diagnose test authserver ldap command provide? (Choose two.)
- A. It displays the LDAP groups found for the user
- B. It displays the LDAP codes returned by the LDAP server
- C. It displays whether the user credentials are correct
- D. It displays whether the admin bind user credentials are correct
Answer: B,C
Explanation:
Explanation
According to the FortiGate CLI Reference Guide, "The diagnose test authserver ldap command tests LDAP authentication with a specific LDAP server. The command displays whether the user credentials are correct and whether the user belongs to any groups that match a firewall policy. The command also displays the LDAP codes returned by the LDAP server." Therefore, options B and C are true because they describe the information that the diagnose test authserver ldap command can provide. Option A is false because the command does not display whether the admin bind user credentials are correct, but rather whether the user credentials are correct. Option D is false because the command does not display the LDAP groups found for the user, but rather whether the user belongs to any groups that match a firewall policy.
NEW QUESTION # 33
Where can FortiGate learn the FortiManager IP address or FQDN for zero-touch provisioning'?
- A. From a DHCP server using options 240 and 241
- B. From a DNS server using A or AAAA records
- C. From an LDAP server using a simple bind operation
- D. From a TFTP server
Answer: B
Explanation:
Explanation
According to the FortiGate Administration Guide, "FortiGate can learn the FortiManager IP address or FQDN for zero-touch provisioning from a DNS server using A or AAAA records. The DNS server must be configured to resolve the hostname fortimanager.fortinet.com to the IP address or FQDN of the FortiManager device." Therefore, option D is true because it describes the method for FortiGate to learn the FortiManager IP address or FQDN for zero-touch provisioning. Option A is false because LDAP is not used for zero-touch provisioning. Option B is false because TFTP is not used for zero-touch provisioning. Option C is false because DHCP options 240 and 241 are not used for zero-touch provisioning.
NEW QUESTION # 34
When you configure a FortiAP wireless interface for auto TX power control which statement describes how it configures its transmission power?
- A. Every 30 seconds FortiGate measures the signal strength of adjacent FortiAP interfaces It will adjust the adjacent AP power to be detectable at -70 dBm
- B. Every 30 seconds FortiGate measures the signal strength of adjacent AP interfaces It will adjust its own AP power to match the adjacent AP signal strength
- C. Every 30 seconds FortiGate measures the signal strength of the weakest associated client The AP will then configure its radio power to match the detected signal strength of the client
- D. Every 30 seconds the AP will measure the signal strength of the AP using the client The AP will adjust its signal strength up or down until the AP signal is detected at -70 dBm
Answer: A
Explanation:
NEW QUESTION # 35
Which two statements about MAC address quarantine by redirect mode are true? (Choose two)
- A. The device MAC address is added to the Quarantined Devices firewall address group
- B. The quarantined device is moved to the quarantine VLAN
- C. It is the default mode for MAC address quarantine
- D. The quarantined device is kept in the current VLAN
Answer: A,D
Explanation:
MAC address quarantine by redirect mode allows you to quarantine devices by adding their MAC addresses to a firewall address group called Quarantined Devices. The quarantined devices are kept in their current VLANs, but their traffic is redirected to a quarantine portal.
NEW QUESTION # 36
Which two statements about the guest portal on FortiAuthenticator are true? (Choose two.)
- A. Each remote user on FortiAuthenticator can sponsor up to 10 guest accounts
- B. Administrators must approve all guest accounts before they can be used
- C. Administrators can use one or more incoming parameters to configure a mapping rule for the guest portal
- D. The guest portal provides pre and post-log in services
Answer: C,D
Explanation:
Explanation
According to the FortiAuthenticator Administration Guide2, "The guest portal provides pre and post-log in services for users (such as password reset and token registration abilities), and rules and replacement messages can be configured." Therefore, option C is true. The same guide also states that "Administrators can use one or more incoming parameters to configure a mapping rule for the guest portal." Therefore, option D is true.
Option A is false because remote users can sponsor any number of guest accounts, as long as they do not exceed the maximum number of guest accounts allowed by the license. Option B is false because administrators can choose to approve or reject guest accounts, or enable auto-approval.
NEW QUESTION # 37
You are configuring a FortiGate wireless network to support automated wireless client quarantine using IOC. Which two configurations must you put in place for a wireless client to be quarantined successfully? (Choose two)
- A. Configure a firewall policy to allow communication
- B. Configure the wireless network to be in bridge mode
- C. Configure the wireless network to be in tunnel mode
- D. Configure the FortiGate device in the Security Fabric with a FortiAnalyzer device
Answer: C,D
NEW QUESTION # 38
Which two statements about the MAC-based 802 1X security mode available on FortiSwitch are true? (Choose two.)
- A. FortiSwitch can grant different access levels to each device connected to the port
- B. FortiSwitch authenticates each device connected to the port
- C. FortiSwitch authenticates a single device and opens the port to other devices connected to the port
- D. It cannot be used in conjunction with MAC authentication bypass
Answer: A,B
Explanation:
Explanation
According to the FortiSwitch Administration Guide, "MAC-based 802.1X security mode allows you to authenticate each device connected to a port using its MAC address as the username and password." Therefore, option B is true because it describes the MAC-based 802.1X security mode available on FortiSwitch. Option D is also true because FortiSwitch can grant different access levels to each device connected to the port based on the user group and security policy assigned to them. Option A is false because FortiSwitch does not authenticate a single device and open the port to other devices connected to the port, but rather authenticates each device individually. Option C is false because MAC-based 802.1X security mode can be used in conjunction with MAC authentication bypass (MAB) or EAP pass-through modes, which are fallback options for non-802.1X devices.
NEW QUESTION # 39
......
Fortinet NSE7_LED-7.0 is an exam that tests the skills and knowledge of network security professionals in deploying and managing Fortinet's LAN Edge solutions. NSE7_LED-7.0 exam is designed for individuals who have experience in managing and securing LAN infrastructure and are seeking to validate their skills in deploying and managing Fortinet's LAN Edge solutions. NSE7_LED-7.0 exam covers topics such as Fortinet's Secure SD-WAN, FortiGate, FortiManager, FortiAnalyzer, FortiSwitch, FortiAP, and FortiNAC.
Fortinet Exam 2024 NSE7_LED-7.0 Dumps Updated Questions: https://www.fast2test.com/NSE7_LED-7.0-premium-file.html
Free UPDATED Fortinet NSE7_LED-7.0 Certification Exam Dumps is Online: https://drive.google.com/open?id=1YpaKIxC5lVbozJf9bRajHbAP9aBOCXba