Online Questions - Valid Practice To your NACE-CIP2-001 Exam (Updated 100 Questions)
Practice To NACE-CIP2-001 - Remarkable Practice On your Coating Inspector Level 2 Exam
NACE-CIP2-001 (Coating Inspector Level 2) Exam is a certification program offered by the National Association of Corrosion Engineers (NACE) International. Coating Inspector Level 2 certification is designed for individuals who work in the field of corrosion prevention and control. NACE-CIP2-001 exam tests the knowledge and skills of candidates in the areas of coating inspection, surface preparation, coating application, and coating inspection equipment.
NEW QUESTION # 41
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Implement immediate to get them motivated
- B. Make sure they are the center of attention in all site meetings
- C. Challenge their value to the team and try to get them out of their comfort zone
- D. Give them as much advance notice as possible about upcoming changes
Answer: D
NEW QUESTION # 42
The Inspectors' goal at the Pre-Job Conference is to:
- A. Obtain a clear understanding of the Specification
- B. Manage the meeting so it doesn't go off topic
- C. Discuss contractual requirements
- D. Take accurate meeting minutes for distribution
Answer: A
NEW QUESTION # 43
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. A very low reading
- B. Cold flow or creep
- C. A very high reading
- D. No difference from any other coating
Answer: B
NEW QUESTION # 44
A single component water borne acrylic coating cures by:
- A. Coalescence
- B. Co-Reaction
- C. Solvent Evaporation
- D. Oxidation
Answer: A
NEW QUESTION # 45
Pre-cleaning of work pieces will NOT remove
- A. oil or grease.
- B. dirt.
- C. mill scale.
- D. snow, ice or water.
Answer: C
NEW QUESTION # 46
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Appearance
- B. Iron content
- C. Cost
- D. Safety
Answer: B
NEW QUESTION # 47
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. False
- B. True
Answer: B
NEW QUESTION # 48
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Verbally challenge the NCR
- B. Consult your supervisor
- C. Review the NCR with the other Inspector
- D. Request a re-blast of the item in question
Answer: B
NEW QUESTION # 49
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Express a willingness to work with the site team and follow the specification
- B. Suggest to the Owner that the supervisor should be removed from site
- C. Defend the previous inspector
- D. Challenge the supervisor's authority
Answer: A
NEW QUESTION # 50
Steel shot grit contaminated with oil or grease used in a cetrifugal blast cleaning should be
- A. disposed of properly.
- B. run through the air wash separator.
- C. mixed with uncontaminated abrasive
- D. washed with clean potable water prior to Use.
Answer: A
NEW QUESTION # 51
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A mechanical adhesion tester
- B. A hardness tester
- C. A destructive paint inspection Tooke gauge
- D. A set of 14 pencils of varying hardness
Answer: C
NEW QUESTION # 52
When ASIN D 3363 is specified the Inspector must:
- A. Use the correct solvent
- B. Record the highest value attained
- C. Record the two end points identified in the standard
- D. Record the percentage of failure
Answer: C
NEW QUESTION # 53
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It will result in a very slippery surface
- C. It doesn't contain biocide
- D. It contains biocide
Answer: D
NEW QUESTION # 54
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Coal Tar Enamel
- B. 2-Layer Polyethylene (PE)
- C. Fusion Bonded Epoxy
- D. 3-Layer Polyethylene (PE)
Answer: D
NEW QUESTION # 55
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Level 1 Inspector
- B. A NACE Level 3 Inspector
- C. Another NACE Level 2 Inspector
- D. A NACE Protective Coating Specialist
Answer: B
NEW QUESTION # 56
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Lower the blast pressure
- B. Increase the standoff distance
- C. a), b) and c)
- D. Move the nozzle quicker
Answer: C
NEW QUESTION # 57
It is always possible to see moisture on a steel substrate:
- A. False
- B. True
Answer: A
NEW QUESTION # 58
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Coal Tar Enamel
- B. Concrete
- C. Heat-shrink sleeves
- D. Liquid epoxies
Answer: D
NEW QUESTION # 59
The most likely area of failure on a buried external pipeline coating is the:
- A. Ground bed
- B. Field joint coating
- C. Areas exposed to Ultra Violet light
- D. Mainline coating
Answer: B
NEW QUESTION # 60
......
NACE-CIP2-001 certification exam is divided into two parts: a written exam and a practical exam. The written exam consists of 120 multiple-choice questions, and candidates have four hours to complete it. The practical exam consists of hands-on inspections of coatings and is designed to test a candidate's ability to apply their knowledge and skills in a real-world setting. Candidates must pass both parts of the exam to earn their NACE-CIP2-001 certification.
NACE-CIP2-001 (Coating Inspector Level 2) Certification Exam is a globally recognized certification program offered by the National Association of Corrosion Engineers (NACE). NACE-CIP2-001 exam is designed to evaluate the knowledge and skills of individuals involved in the inspection and management of coating projects. Coating Inspector Level 2 certification program is widely recognized by industries such as oil and gas, marine, aerospace, and construction, and is a valuable credential for professionals seeking advancement in their careers.
True NACE-CIP2-001 Exam Extraordinary Practice For the Exam: https://www.fast2test.com/NACE-CIP2-001-premium-file.html
Get 100% Passing Success With True NACE-CIP2-001 Exam: https://drive.google.com/open?id=14yFB4N9WxT4lQmukJYVzim8s8SB3MuuD