[Sep-2021] Get 100% Real HPE0-V14 Exam Questions, Accurate & Verified Fast2test Dumps in the Real Exam! [Q128-Q150]

[Sep-2021] Get 100% Real HPE0-V14 Exam Questions, Accurate & Verified Fast2test Dumps in the Real Exam!

Pass Your HPE ATP - Hybrid IT Solutions V2 Exams Fast. All Top HPE0-V14 Exam Questions Are Covered.

NEW QUESTION 128
A customer is planning to deploy a new Top of Rack solution. They plan to use a stacking technology that meets the following requirements:
* Support for Multi Chassis Link Aggregation in an active-active mode.
* The control plane must not be a single point of failure.
* Rapid Fail-over.
* Unified Management.
* They require a maximum of two switches per stack.
Which stacking technology meets the customer's requirements?

A. HPE Distributed Trunking
B. HPE Intelligent Resilient Framework (IRF)
C. Aruba Virtual Switching Extension (VSX)
D. Aruba Virtual Switching Framework (VSF)

Answer: C

Explanation:
Explanation/Reference: https://www.arubanetworks.com/assets/tg/AVD_Midsize-Campus-Design-Deploy.pdf

NEW QUESTION 129
When is it appropriate for a customer to implement HPE OneView Standard?

A. To monitor their services
B. To enable the Advanced iLO license
C. To update firmware
D. To manage multiple servers

Answer: A

Explanation:
Reference:
https://h20195.www2.hpe.com/v2/GetPDF.aspx/c04111367.pdf

NEW QUESTION 130
A customer needs to provide inventory management, health monitoring, status alerting, and reporting for their ProLiant servers.
Which HPE management offering meets the customer's needs?

A. Insight Online
B. Insight Remote Support
C. OneView
D. InfoSight

Answer: C

NEW QUESTION 131
Match each characteristic to the appropriate RAID level.

Answer:

Explanation:

NEW QUESTION 132
Read the question, and then refer to the exhibit.
<Switch-A>display interface Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet1/0/1 Current state: Administratively DOWN Line protocol state: DOWN IP packet frame type: Ethernet II, hardware address: d894-03fb-793d Description: Ten-GigabitEthernet1/0/1 Interface Bandwidth: 10000000 kbps Loopback is not set Media type is stack wire, port hardware type is STACK_SFP_PLUS Unknown-speed mode, unknown-duplex mode Link speed type is autonegotiation, link duplex type is autonegotiation Flow-control is not enabled Maximum frame length: 10000 Allow jumbo frames to pass Broadcast max-ratio: 100% Multicast max-ratio: 100% Unicast max-ratio: 100% PVID: 1 MDI type: Automdix Port link-type: Trunk VLAN Passing: 10, 20 VLAN permitted: 10, 20 Trunk port encapsulation: IEEE 802.1q Port priority: 0 Last link flapping: 0 hours 0 minutes 18 seconds Last clearing of counters: Never Peak input rate: 78 bytes/sec, at 2011-03-31 04:55:57 Peak output rate: 15 bytes/sec, at 2011-03-30 23:00:57 Last 300 second input: 0 packets/sec 67 bytes/sec - % Last 300 second output: 0 packets/sec 14 bytes/sec - % Input (total): 62670 packets, 8565340 bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input (normal): 62670 packets, - bytes 0 unicasts, 0 broadcasts, 62670 multicasts, 0 pauses Input: 0 input errors, 0 runts, 0 giants, 0 throttles 0 CRC, 0 frame, - overruns, 0 aborts - ignored, - parity errors Output (total): 3707 packets, 1294835 bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output (normal): 3707 packets, - bytes 0 unicasts, 0 broadcasts, 3707 multicasts, 0 pauses Output: 0 output errors, - underruns, - buffer failures 0 aborts, 0 deferred, 0 collisions, 0 late collisions 0 lost carrier, - no carrier A customer added a new switch to their network. They connected it using interface Ten-GigabitEthernet 1/0/1. They are using VLAN 10 and 20 for the devices in their network.
The new switch was fully operational. Then, the customer experienced a power failure later that day and could not reach any device on the new switch after the power returned.
From the output in the exhibit, would could be the issue?

A. The interface link-speed and duplex are unknown.
B. The interface is administratively down.
C. The interface is configured for a PVID of VLAN 1.
D. The interface loopback is not set.

Answer: C

NEW QUESTION 133
Match the characteristic to the correct HPE ProLiant family.

Answer:

Explanation:

NEW QUESTION 134
An HPE customer wants to perform is simplified update of firmware and drivers among their 100 HPE Gen9 and Gen10 racked servers.
Which HPE software tool should the customer use to minimize the time required to perform this activity.

A. HPE ProLiant Support Pack
B. HPE Smart Update Manager
C. HPE iLO Amplifier Pack
D. HPE OneView Standard

Answer: B

Explanation:
Reference: https://www.hpe.com/us/en/servers/smart-update.html

NEW QUESTION 135
Match each characteristic to the appropriate RAID level.

Answer:

Explanation:

Explanation

NEW QUESTION 136
What is an access port on an Ethernet switch?

A. A port that carries multiple VLANs
B. A port that carries FCP frames inside the network
C. A port that carries untagged frames inside the network
D. A port that is connected to an FCF

Answer: C

Explanation:
Reference: https://support.hpe.com/hpesc/public/docDisplay?docId=mmr_kc-0102233

NEW QUESTION 137
Indicate whether each management feature manages or monitors a single system or multiple systems.

Answer:

Explanation:

NEW QUESTION 138
An HPE customer wants to perform is simplified update of firmware and drivers among their 100 HPE Gen9 and Gen10 racked servers.
Which HPE software tool should the customer use to minimize the time required to perform this activity.

A. HPE ProLiant Support Pack
B. HPE Smart Update Manager
C. HPE iLO Amplifier Pack
D. HPE OneView Standard

Answer: B

Explanation:
Reference:
https://www.hpe.com/us/en/servers/smart-update.html

NEW QUESTION 139
A client complains about systems reliability issues caused by their staff's inability to identify the root cause of failures. The client's lead administrator wants to automatically send data from HPE OneView to additional listeners in the network.
What should you configure in HPE OneView to enable the external monitoring of the managed devices?

A. Configure scheduled reports to export the data to the listener.
B. Configure a scope to include the listener.
C. Configure SNMP Trap Forwarding.
D. Configure the listener as a managed device.

Answer: C

Explanation:
Reference:
https://h20195.www2.hpe.com/v2/getpdf.aspx/4AA5-3811ENW.pdf?

NEW QUESTION 140
A customer has a small business office and is concerned that the local storage in their current ProLiant Gen 10 server with a Linux OS Is reaching maximum capacity Which solution should you recommend to expand the customers data storage capacity?

A. StoreEver
B. D3000
C. SimpliVity
D. StoreOnce

Answer: B

NEW QUESTION 141
Match the feature to the lowest iLO5 license in which it is available

Answer:

Explanation:

Explanation
Last - last
3-2
1-1
3-3

NEW QUESTION 142
Refer to the exhibit.

You are designing a new Nimble AF40 for your customer. The array will be added into an existing Nimble HF60 environment connected with SN6000B switches. You have created the configuration shown in the exhibit and noticed an error What should you change in your configuration to ensure it meets the customer requirements?

A. Change the controller to an HF20H.
B. Change the 10GbE Optical ports to 10BaseT.
C. Change the controller to an AF20.
D. Change the 10GbE Optical ports to Fibre Channel.

Answer: D

NEW QUESTION 143
A customer plans to use HPE ProLiant servers for an application that requires low latency for all components.
Which workload profile should the customer use?

A. Transactional Application Processing
B. Mission Critical
C. I/O Throughput
D. Virtualization - Max Performance

Answer: B

NEW QUESTION 144
A customer has the following requirements:
two or more 10Gb SFP+ uplinks
downlink ports capable of 1Gb or 10Gb operation over CAT6a or CAT7 cables
24 downlink ports Which HPE tool would you use to help choose an HPE network solution that meets the customer requirements?

A. HPE Switch Selector
B. HPE SPOCK
C. HPE NinjaSTARS
D. HPE SAF

Answer: B

NEW QUESTION 145
Match the speed and protocol with the appropriate component.

Answer:

Explanation:

Explanation

Reference:
https://buy.hpe.com/us/en/options/transceivers/server-transceivers/hpe-sfp-transceivers/p/7263510
https://itg.buy.hpe.com/emea_europe/en/options/transceivers/server-transceivers/server-transceivers/hpe- qsfp28-transceivers/p/1008789459

NEW QUESTION 146
A customer just purchased a ProLiant 300 series Gen10 server and wants to install the latest version of Windows.
Which feature of this server will assist the customer with the initial Windows installation?

A. Smart Storage Administrator
B. HPE SmartStart
C. HPE SSA Diagnostics
D. Intelligent Provisioning

Answer: D

Explanation:
Explanation/Reference: https://community.hpe.com/t5/Alliances/Get-HPE-Gen10-Servers-with-Windows-Server-2019-up- and-Running-in/ba-p/7066128#.XnxeVG5RWQ4

NEW QUESTION 147
Match the Networking Product Family to the appropriate use case:

Answer:

Explanation:

NEW QUESTION 148
A customer needs to deploy an application on a newly-installed HPE ProLiant server, but they report that the server is not online. They call you for remote support. The IP address on the production network cannot be reached. You are evaluating the probable root causes of this issue.
According to the troubleshooting methodology, what are next two steps? (Select two)

A. Remote console into the ToR switch to check the server's port configuration.
B. Use Microsoft Remote Desktop or VNC to check the server's NIC and IP address configuration
C. Use OneView to see f the server firmware is up-to-date
D. Run insight Diagnostics on the Server
E. Log in to iLO to see if the server hardware and NIC are online and configured correctly.

Answer: D,E

NEW QUESTION 149
Refer to the exhibit.

A customer purchased a server/storage environment shown in the exhibit with 1 Gb networking connectivity.
The customer is now experiencing performance issues.
Identify the correct components to upgade the network connections and improve performance on the left. Then drag those components to the answer area on the right. (Choose three.)